Subscribe to Our Youtube Channel
Summary of Contents for Stermay M1
- Page 1 UNDERWATER SCOOTER USER MANAUL STERMAY M1 Please read the operation instructions carefully before using this product. Please operate in the correct way based on complete understanding.
- Page 2 Thank you for you choice STERMAY M1! STERMAY M1 is one type technology products which able to provide thrust power for you under water. It has small body, portable and disassemble structure, easy to carry, use and renewal. Machine body bottom set integrated type outer configured sliding rail, coordinate the switch part according to your requirements, able to carry different outer configure equipment (SUP, sport camera, lighting lamp, etc).
- Page 3 STERMAY Caution！ ！This device complies with Part 15 of the FCC Rules / Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference. (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 4: Table Of Contents
7. Outer configure equipment installation 2.1 Safety warnings.......03 methods 3. Product Introduction 7.1 Install the M1 on the SUP......13-14 7.2 Install the sport camear on the M1....15 3.1 Package list ........06 3.2 Specification ........06 8. Maintenance 3.3 Product diagram......07 8.1 Cleaning after use ........16 4. -
Page 5: Product Overview
STERMAY M1 able to assort the switch part to connect the over water carriage tools such as canoe to use, also able to carriage underwater sport camera, lighting lamp and other equipment to record the underwater beautiful moment . - Page 6 STERMAY ！This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Page 7 ！Only use the charger equipped with the M1 underwater thruster. ！Only use the supply unit provided with M1 appliance to charge the battery.Other chargers are not allowed. ！Connect the charger into electric circuit first then connect the charger with battery when battery charging.
-
Page 8: Product Introduction
STERMAY 3. Product Introduction Package list ·Main Unit*1 ·Remote Handle*1 ·Handle*1 ·Bettery*1 ·Switching power ·O Ring*2 ·Camera Bracket*1 supply*1 ·Connect Bracket ·Connect Bracket ·Type-C*1 ·Typy-C adapter*1 ·Remote handle anti ·Remote handle anti ·User Manual*1 lose rope (long type)*1 lose rope(short type)*1 Specification... -
Page 9: Product Diagram
STERMAY 3.3 Product diagram Display screen Start-stop button Top View Track Handle Lock Reomte Handle Power switch Handle Main Unit Head Cover Fast disassemble Handle Lock Bottom View Tail Cover... -
Page 10: Assembling Instruction
STERMAY 4. Assembling Instruction Fast Disassemble 4.1 Install the Battery Button 1.Press the Fast Disassemble Button to remove the Head Cover. 2.Push the Battery into cabin according the shape of Battery Tighten Nut Compartment until the bottom. 3.Force to tightly insert after make the Fix Position Groove of power supply joint outer wall on Main Unit corresponding to the Convex Rib on internal wall of battery power supply joint. -
Page 11: Handle Assembling
STERMAY Handle assembling 1. Main Unit is placed with the Display Screen as the front。 2. Take out the Handle ,Remote Handle. 3. Kindly pay attention to check the front and back directions of Handle and Remote Handle installations,so that the Remote Handle is in right of Main Unit. -
Page 12: Charging Instruction
STERMAY 5. Charging Instruction Battery charging Remote Handle charging 1.Connect the plug pins of Switching Power Supply to the AC 1.Open the Seal Cover of Type-C of Remote Handle. power. 2.Please use 5V/1A power adapter or standard USB charger 2.Connect another end of Switching Power Supply to Battery port to charge. -
Page 13: Operating Instruction
The corresponding icons of three speed setting on Main Unit display screen shown as below: Medium HIGH 5. Press the Start-stop Button to run M1, release it down to stop. switch 6. Long press the F Key and Power respectively to power Type-C off... -
Page 14: How To Use When Suspended On Sup
1.The operation steps for power-on and signal connection same to 6.1 (How to use when dinving). 2.After the Main Unit and Remote Handle signal are connected,the M1 suspended on SUP start working when press down M Key on Remote Handle. -
Page 15: Outer Configure Equipment Installation Methods
7.Outer configure equipment installation methods Connect Bracket A 7.1.1 Install the M1 on SUP (By the Connect Bracket A) 1.Make the Connect Bracket A align to the Track of Main Unit,and slide the Connect Bracket A into the Main Unit until the screw Track holes of both are aligned. - Page 16 STERMAY 7.1.2 Install the M1 on SUP(By the Connect Bracket B) 1. The installation method of connecting bracket B and Main Unit Connect Bracket B is the same as that of connecting bracket A. 2. After the installation, the Main Unit with Connect Bracket B should be keep a tilt angle with the SUP mounting base.
-
Page 17: Install The Sport Camear On The M1
STERMAY Underwater Sport Install the sport camear on the M1 Camera (Not Provided) 1.Make the Camera Bracket align to the Track of Main Unit,and Bolt 2 slide the Camera Bracket into the Main Unit until the screw holes of both are aligned. -
Page 18: Maintenance
6.Place the Main Unit and battery at cool and air venting place to completely dry it then storage. 8.2 Storage 1.Please storage M1 in a dry place at room temperature , keep better air venting environment, avoid direct sunshine. 2.Keep away from heat,fire and children’s reach. -
Page 19: Warranty Policy
！From the date of purchase, we could provide maintenance service for the fault of the product itself that inspected and confirmed STERMAY or its authorized maintenance station,according to the warranty period of the host and the parts which specified as... - Page 20 Manufacturer: JIANGSU YOUMAY ELECTRIC APPLIANCE CO., LTD Manufacturer's address: No. 20 YuLan Road, XuYi Economic Development Zone, XuYi County, HuaiAn city, JiangSu Province, China...
Need help?
Do you have a question about the M1 and is the answer not in the manual?
Questions and answers