Xiwxi N09-A - Wireless Earbuds Manual

For a good user experience, please read the manual carefully before using the products. Notice: To avoid unnecessary troubles, please do not disassemble these products by yourself, and please use the standard charger to charge.

Product overview

Wearing

1. Choose the ear cap that suits you.
   
   
2. Make sure that the ear caps face down and put the earbuds into the ear in the angle shown as the picture below.
   
   
3. After putting on the earbuds, gently rotating the earbuds to a comfortable and secure position shown as picture below. Now the earbuds are put on correctly!
   
   
4. Error demonstration
   Do not wear the earbuds like the way shown as the picture below.
   

First time using

1. Tear off the insulating film.
   
   
2. Put the earbuds into the charging case to charge.
   
   
3. Take out from case, the indicator will turn to Red and Blue alternately.
   
   Warm notice: If the earbuds are not turned on or there is no sound come out, please put them back in the charging case again to make sure that they are in the charging state before taking them out for use.
4. The indicator of one earbud will go off and another will flash red and blue light alternately. (In pairing mode)
   
   
5. Turn on the Bluetooth function on your phone and search for【N09-A】and connect it.
   

Warm notice

• If the left/right earbuds can't be paired or no sound, please turn off the Bluetooth of the mobile phone, when the red/blue lights of the earbuds flash alternately, tap any earbud for 3 times to re-pair. One earbud's indicator turns off, another one's indicator flashes red and blue alternately(in pairing mode)
• If you want to switch the Bluetooth connection to another device, please disable the Bluetooth function in the previously connected device OR delete the pairing name of "N09-A" from the original device. Then the pairing name of "N09-A" can be searched in new device and connected successfully.

Button control

Take-out from case OR press and hold for 5 seconds.

When back into case OR no connection for 5 minutes.

Warm notice
For any single earbud, when it is in standalone mode, you can't use it to play the previous song or decrease the volume.

Siri and other Voice Assistant

iOS and part of the Android users can triple click the left or right power switch to turn on the voice assistant.

The voice assistant will be automatically activated depends in different OS in mobile system.

Restore factory setting

1. When the earbud is on with mobile phone unconnected, click the left and right power switch simultaneously four times quickly. The red and blue lights will be on for 2 seconds and then it will clear its memory and the earbuds will shut down.
   
   
2. Please delete all paired records on the phone and search again for "N09-A"on the Bluetooth of mobile phone and reconnect.
   

Earbuds indicator

Charging case indicator

Specifications

Charging

Note: Please put both earbuds in the charging case to fully charge them on first use.

Charging case

Please use a charger with an output voltage of DC5V/1A to charge the charging case. You can also use a computer USB or other USB interface charger to charge (Must choose a charger certified by a regular manufacturer).

Charge warning

While charging, do not press the earbud power button, which will cause pairing failure, then you need to reset.

Signal transmission distance shown as below:

Notice:

1. If the charging case is out of power, it may cause the earbuds to fail to shut down and remain connected to the phone even when they are placed in the charging case. So please remember to charge the charging case in time.
2. If moisture remains at the audio output hole, the sound may become fuzzy or completely inaudible. This is completely normal. In this case, please remove the earplugs and shake the audio output hole down several times to allow water to flow out or let it air dry for 1-2 hours, then the sound quality will become normal.
   
   
3. If there is noise, broken sound, or low sound, please take off the silicone ear cap and wipe it with a cotton swab.
   
   
4. If the earbud is not charged properly, wipe the charging column with a cotton swab, and then charge it again.
   

Attentions

The Charging cable is not waterproof

The Charging case is not waterproof

Do not use hot water to disinfect the product

If there is water droplet on the surface, please wipe it with a dry cloth before putting them back into the charging case to avoid damaging the device.

Tip:

1. If the product is dirty, please do not rinse it directly with water or use boiling water to soak and disinfect it. It is recommended to wipe the earbuds with an alcohol cloth or a wet paper towel.
2. If the product falls into the water accidentally, please pick it up in time and dry it with natural wind or dry it in the sun for two hours before using it. (Otherwise it will affect the sound quality, thus fail to give you a better using experience)

Cleaning

1. Do not use corrosive liquid to clean this product.
2. If it comes into contact with chemicals, please rub it with a damp cloth wet with clean water.
3. Do not use this product under extreme circumstances for temperature below -10 degree Celsius or above 60 degree Celsius.
4. To avoid explosion, please do not throw this product into fire.
5. To avoid scratches, please do not touch the earbuds with sharp objects.
6. Do not insert objects into the earbuds, otherwise it would cause damage to the internal components.
7. Do not disassemble the earbud.
8. Please keep regular charge to earbuds, don't leave them become empty battery status to keep their lifetime.
9. Please do not charge products with power adapter over 2A current. Excessive current may cause the damage to battery.

Battery Warning! There is a built-in lithium battery in this product. To avoid explosion, do NOT expose the product to strong sunlight, fire or throw it into fire.