Mitsubishi Electric Unisen LT-40164 Basic Owner's Manual
154 series, 164 series, 265 series immersive sound led lcd hdtv with integrated sound projector
Hide thumbs
Also See for Unisen LT-40164:
- Specifications (2 pages) ,
- Service manual (70 pages) ,
- Basic owner's manual (40 pages)
Table of Contents
Advertisement
IMMERSIVE SOUND LED LCD HDTV
with Integrated Sound Projector
MODELS
154 Series
164 Series
265 Series
BASIC OWNER'S GUIDE
This manual provides basic connection, setup, and operating instructions. Please visit our website at
www. Mitsubishi-tv.com to view or download a detailed owner's guide that fully describes the features
of this TV. Follow the Support link to the Product Documents page.
•
For questions:
-
Visit our website at www.mitsubishi-tv.com.
-
E-mail us at MDEAservice@mdea.com.
-
Call Consumer Relations at
•
For information on
•
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call
800-553-7278.
265 Series.
•
IR emitter cables for NetCommand home-theater control are available for purchase from
Mitsubishi. Call 800-553-7278 and request either part number 242D483020 (two-ended cable) or part
number 299P254020 (four-ended cable).
800-332-2119 for operational or connection assistance.
System Reset, please see the back cover.
®
Advertisement
Table of Contents
Related Manuals for Mitsubishi Electric Unisen LT-40164
Summary of Contents for Mitsubishi Electric Unisen LT-40164
- Page 1 This manual provides basic connection, setup, and operating instructions. Please visit our website at www. Mitsubishi-tv.com to view or download a detailed owner’s guide that fully describes the features of this TV. Follow the Support link to the Product Documents page.
-
Page 2: Fcc Declaration Of Conformity
TV WEIGHT: This TV is heavy. Exercise extreme care when lifting or moving it. Lift or move the TV with a minimum of two adults. To prevent damage to the TV, avoid jarring or moving it while it is turned on. Always power off your TV, unplug the power cord, and discon- nect all cables before moving it. -
Page 3: Table Of Contents
First, turn off the TV and unplug the power cord from the power outlet. Occasionally clean dust build-up from the air-intake grilles on the back and sides of the TV. Clean using a vacuum cleaner with a brush attachment. Top and Sides of the TV •... -
Page 4: Important Safety Instructions
(NE C AR T 250, P AR T H) Outdoor Antenna Grounding If an outside antenna or cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. -
Page 5: Stand Installation
• At least TWO PEOPLE are required to install the stand. Support the TV near the corners as shown. Failure to follow these recommendations may result in personal injury and damage to the product. -
Page 6: Wall-Mounting
Stand Removal Prior to Wall-Mounting At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other person removes the stand. Failure to follow these recommendations may result in personal injury and damage to the product. -
Page 7: Before You Begin
Choose a location for your TV. • See the stand-installation or wall-mounting requirements starting on page 5. • Allow at least four inches of space on all sides of the TV to help prevent overheating. Over- heating may cause premature failure of the TV. • Avoid locations where light may reflect off the screen. Install the batteries in the remote control. -
Page 8: Remote Control
TV. • 265 Series. Perform NetCommand setup of device keys. See the detailed owner’s guide at www.mitsubishi-tv.com for information. For assistance call 1(800) 332-2119 Emitter-Bulb End TV CAB/SAT DVD AUDIO VCR Press the key for the device type to control. -
Page 9: Setting Up And Using Tv Inputs
ANT input. Refer to page 16. You must perform a channel scan to enable recep- tion of digital channels. If you skip this step, the TV will receive only analog channels. The channel scan will search for high-definition and standard-definition channels available in the local area. - Page 10 Setting Up Other Inputs Power on the TV. Power on the devices to ensure detection. Connect one device to the TV, making note of the TV input jack. The TV will display the New Device Found screen if the connection type is detectable.
-
Page 11: Basic Tv Operation
TV. • If LED continues to flash red and yellow after reset, turn off the TV and unplug it from the AC power source. Wait one minute and then plug the set back in. • If LED continues to flash red and yellow, www.mitsubishi-tv.com or call 1-800-332-2119 to receive... -
Page 12: Channelview Channel Listings
More TV Features Features covered in this Basic Owner’s Guide include: Feature Parental controls (Lock menu) TV Clock. Set the TV Clock if you plan to use the TV Timer (page 27) or ChannelView (page 17). Favorite sources ChannelView channel listings Changing input names in the Input Selection menu (Inputs >...