Advertisement
Quick Links
Table of Content
Introduction...........................................................................................................02
Check list..............................................................................................................02
Front view .............................................................................................................03
Rear view ..............................................................................................................03
CAS system ..........................................................................................................04
Install the Dedicated Driver on PC ........................................................................................05
Core Audio Stream Introduction...............................................................................................07
WASAPI Setting.......................................................................................................................08
Setting on Mac OS...................................................................................................................10
Specification ............................................................................................................................10
FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
2. Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment
Note:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection again
st harmful interference in a residential installation.This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
inerference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipme
nt does cause harmful interference to radio or television reception, which can be determined by turning t
he equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, Human proximity to
the antenna shall not be less than 20cm (8 inches) during normal operation.
1
Advertisement
Summary of Contents for Questyle Audio T2
-
Page 1: Table Of Contents
Table of Content Introduction……………………………………………………..…………………..…………02 Check list…………………………………………………….…..…………………..…………02 Front view …………………………………………………….…..…………….……..……….03 Rear view …………………………………………………….…..……………..……..……….03 CAS system …………………………………………………….…..…………..………..……04 Install the Dedicated Driver on PC ..................05 Core Audio Stream Introduction....................07 WASAPI Setting........................08 Setting on Mac OS........................10 Specification ..........................10 FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. -
Page 2: Introduction
2.4GHz frequency interference, achieve more stable transmission. T2 Transmitter support digital input with USB, Coaxial and optical. It can also receive analogue signal through RCA input, with built-in ADC to convert to digital signal for transmission. It’s easy operate, can work automatically after power on. -
Page 3: Rear View
1) USB input indicator 2) SPDIF input indicator 3) Toslink input indicator 4) Analog input indicator 5) Input select button 6) Volume down 7) Volume up Rear View 1) DC power input 2) Right channel Analog input 3) Left channel Analog input 4) SPDIF input 5) TOSLINK input 6) USB input, type B... - Page 4 Pair T2 with R100 or R200. 2. Pairing T2 Transmitter with R100/R200 Wireless Amplifier T2: Long press the “INPUT” button (on front panel) for over 3 seconds, until 4 LED indicators starts flashing (flash lasts for 60 seconds). It means T2 is ready for pairing.
-
Page 5: Cas System
Communication between T2 and PC is real-time and it has some requirements for PC hardware and software platforms. If the platform is bad or the PC is very busy, it will cause T2 to work unstably as well as some other abnormal statuses. In such cases, try to run the dpclat. -
Page 6: Install The Dedicated Driver On Pc
Install the Dedicated Driver on PC After being installed the driver, PC will recognize T2 . Here we take Win7 32 bit operation system as an example to tell the installation procedure. 1） Power on T2 2） Plug the USB cable to connect PC with T2. - Page 7 Click “Install”...
- Page 8 5) Click "Finish" and restart the PC. By now, the T2 finishes installation. 6) Installation on Win XP or Vista OS is the same. Note: T2 will automatically remember the connected USB port, in next time onward please connect the same USB port.
-
Page 9: Core Audio Stream Introduction
If you don't set the output to be the core audio stream, you will find the sample rate shown on T2 is different from that of playing the original music, and it is locked at 48K or 44.1K. When you finish the following settings, you will find that the shown sample rate is the same as that of... - Page 10 JRiver setup Let’s take Win 7 32bit operating system as example, to see how to setup JRiver Media Center. 1. Download and install 1) Click the website http://www.jriver.com/download.html , click “Windows Download” to download the JRiver Media Center 19. 2) Install JRiver Media Center 19. 2.
- Page 11 Click “Add...”, then next screen click “Browse”, find the file where the music stays, then click “OK” to complete it.
- Page 12 3. JRiver output setup 1) In “Tool” option there is a “Option” menu, click it to entry sub menu. 2) In “Audio” menu, find the “Audio output”, choose “SPDIF Out (Questyle High-end USB Audio Device) [WASAPI] “, then click “OK”. 3）With above setting, now CAS192D can play the music files from your Windows PC (exclude DSD files);...
-
Page 13: Setting On Mac Os
On MAC OS, all of the features including the standard asynchronous transfer mode of T2 won’t change. After connecting T2 to PC with USB cable, you need to manually set the output device to be “SPDIF Output”, and then the whole system can work. As shown below:...