Advertisement
Quick Links
Advertisement
Summary of Contents for Impac Tradesman 2000
- Page 1 2022 INSTALLATION MANUAL Tradesman 2000...
- Page 2 TABLE OF CONTENTS PREPARE FOR INSTALLATION ------------------------------------------------------------------ 1 INSTALLATION SAFTEY -------------------------------------------------------------------------- 2 PARTS LIST ------------------------------------------------------------------------------------------ 3 INSTALLATION FORD, DODGE, CHEVY, TOYOTA------------------------------------------- 4-9 CONNECTING ELECTRICAL CABLES ---------------------------------------------------------- 10 CONNECTING HYD LINES------------------------------------------------------------------------ 11 FINISH FRAME CONSTRUCTION / CHECK REMOTE AND HYDRAULIC FLUID-------- 12 VIBRATION BRACKET INSTALATION --------------------------------------------------------- 13 SCHEMATICS -------------------------------------------------------------------------------------- 14-15 INSTALATION HELP SHEET ---------------------------------------------------------------------- 16...
- Page 3 IMPAC 2000 TRADESMAN INSTALLATION HARDWARE PARTS LIST ITEM PART NUMBER DESCRIPTION IMP735 BOLT HEX 5/16"-18X3/4" SS IMP649 HEX BOLT 5/16"-18 X 1-1/4 SS IMP806 BOLT HEX 5/16"- 18 X 4-1/2 SS IMP579 WASHER FLAT 5/16"SS IMP498 NUT, NYLOCK 5/16"-18 SS IMP882 GROMMET RUBBER 1-1/2"...
- Page 4 Completely empty the truck bed. Once empty it is recommended that the bed be power washed prior to installa- tion. Bed Liners Spray-in bed liners provide an acceptable mounting surface for Impac lift installations. However, hard plastic drop-in bed liners must be removed from the truck bed in order to provide a solid mounting suitable for installing IMPAC-Lift.
- Page 5 IMPAC 2000 STANDARD Before beginning the installation remove the packing material to expose the Impac Lift on the pallet. LEAVE BOTH FRAMES SECURED TO THE PALLET. Carefully inventory the items identified in the illustration above. Check the items in the hardware package against the list on page 3 of this manual. If any items are missing contact...
- Page 6 Installation Ford, Dodge, Chevy & Toyota Section This section applies to the Boom Arm Frame installation on Ford, Dodge, Chevy and Toy- ota trucks only. Foot Plate Position for Chevy Foot Plate Position for All Models Except Chevy Step 1 Step 1 Step 1—...
- Page 7 Fig. B Fig. A Step 2—Take the unit frame that has the hydrau- Step 6— With the lic pump and place it on the drivers side of the pick up units pulled back feed truck bed with the arm end pointing forward toward the RED Electrical cable truck cab.
- Page 8 Squaring the Unit to Bed Securing unit to truck bed Step 10— Align the edge of both units with the end of the Step 12— Align the 5/16” drill bit through the holes in the front foot bracket and drill through the truck bed floor. truck bed post.
- Page 9 IMPAC 2000 TRADESMAN Rope Placement...
- Page 10 IMPAC Tradesman 2000 Bar Installation Insert the hoist cables through the bottom of the boom up to the winch. Insert boom into arms carefully without damageing hoist cables. Insert 4 1/5" bolts. (BECAREFUL ON DRIVER SIDE NOT TO DAMAGE HOIST...
- Page 11 TRADESMAN 2000 CROSS BAR MOUNTING...
- Page 12 Connecting the Electrical Cables VERY IMPORTANT Disconnect the Fuse Box off the Long Red Cable. Run the Long Red and Black Cable under the truck bed and attach it to the chassis with the supplied tie wraps. Pass the ends up into the engine compartment and reconnect Long Red Cable to the Fuse Terminal.
- Page 13 CONNECTING AND SECURING ALUM HYDRAULIC LINES STEP 2 STEP 1 CONNECT THE DRIVER SIDE RUBBER HOSE LINES TO THE ALUM WITH THE PROVIDED SCREWS (IMP1100) SECURE THE ALUM HYD LINE ACCORDANLY BY COLOR RED TOP LIKE IN (FIG A) ALSO HYD LINE TO THE BED BULK HEAD WALL.
- Page 14 Finish Frame Construction It will probably be necessary to tap in the cross bar end caps with the rubber mallet. Attach the Side Access Panels to both sides of Do not remove until ready to operate. the Unit Arm Frames. Finally, cut the shipping straps band off the arms.
- Page 15 IMPAC VIBRATION BRACKET 2022 (FIG 2) (FIG 1) (FIG 2) USE PROVIDED VIBRATION BARCKET FOR BED HEIGHT OF 20.1" USE THE EXTENDER FOR BED HEIGHT TALLER THAN 20.1" UP TO 22.4" Step 1 - Loosen lower bumper pad bolt. (FIG. 1) Step 2 - Align bracket with bed rail.
- Page 17 HOSE MARKED RED TOP TRUCK CAB PARTS LIST FOR HYDRAULIC PART QUANTITY DESCRIPTION ITEM NUMBER IMP2014 CYLINDER ALUM HYD IMP1051 LINE 1/4 JIC-M X IMP1054 1/2 MORB 90 ELBOW 1/4 JIC-M X IMP1026 1/2 MORB STRAIGHT HYD TEE 1/4 JIC-M X 1/4 IMP856 JIC-M X1/4JIC-F...
- Page 18 IMPAC 2000 Installation Help Sheet Place spreader bars with 4 (2 x 6 x 12 pieces of wood) in bed to square the unit. When installing Power Cord drill hole before setting unit all the way to left side of bed. Run power line through hole and set unit with spreaders next to left bed wall.
- Page 19 Notes...
- Page 20 Notes 05/25/2022...