J5create ScreenCast JVAW62 Quick Start Guide

1. Simply plug into a laptop or mobile device
   Plug the JVAW62 TX into a USB-C® port on a laptop or mobile device. Wait a few seconds until the flashing light on the JVAW62 TX stops, and it will start mirroring automatically. If the JVAW62 TX flashes for more than 20 seconds, unplug it and then plug it back in. If it flashes for more than 20 seconds again, it will need to be paired to the JVAW62 RX*.
   * See the section titled "How to pair the JVAW62 TX with the receiver" below for instructions on how to pair the TX with the RX.
   
   
2. Stop and restart mirroring Press the JVAW62 TX button to stop or restart mirroring.
   
   Note: The JVAW62 TX supports mirroring for all laptops and mobile devices running Windows®, macOS®, iPadOS®, and Android™ operating systems. The USB-C® port on the device must also support DP™ output.

Position the ScreenCast for an Optimal Streaming Experience

The USB™ Type-A connector can be attached to your TV with the double-sided adhesive strip that is included. The strip is for single-use and can be removed.

The USB™ Type-A connector is equipped with a Wi-Fi® module, antenna, and power supply; therefore, we DO NOT recommend placing the USB™ Type-A connector behind the TV or inside a TV cabinet. Doing so may cause a weak signal or loss of signal.

Adhesive Strip Instructions

1. Choose a at surface to attach the USB™connector. Make sure the area is clean before attaching.
   
   
2. Remove the liner from the double-sided adhesive strip.
   Press adhesive to the bottom of the USB™ connector.
   
   
3. Remove the other liner.
   Firmly press the USB™ connector to the desired location for 30 seconds.
   

Troubleshooting: How to pair the JVAW62 TX with the receiver

1. Turn on pairing mode for the receiver
   Press the reset button (or insert the pin to press) for 2 seconds on the JVAW62 wireless display receiver. Release the button when the screen shows "Release the button to pair with ScreenCast". Please make sure your receiver has been upgraded to the latest version.
   For instructions on how to upgrade your device please visit https://j5create.com/screencast/
   
   
2. Press the JVAW62 TX button
   Plug the JVAW62 TX into the laptop or mobile device to provide power.
   Press the JVAW62 TX button to complete pairing when the screen shows "Ready to pair".
   

Note:
The reset button on the receiver has 3 functions, which function is performed depends on the duration the button is held down.

1. Simple click: Switch the receiver to 2.4G/ 5 GHz Wi-Fi® mode.
2. Press for 2 seconds: Turns on pairing mode for the JVAW62 TX.
3. Press for 10 seconds: Resets the receiver to default.

FCC Warning Statements

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

FCC RF Exposure Warning

• This device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.
• The product is restricted for indoor use only.

Limited Warranty

j5create offers a limited 1-year warranty. User's wear & tear damage is not included. The user shall call or email j5create customer service with the defect information of the product and obtain a return authorization number.

For more information please visit our website at http://www.j5create.com
Copyright© 2022 j5create. All rights reserved. All trade names are registered trademarks of their respective owners. Features and specifications are subject to change without notice. Product may not be exactly as shown in the diagrams.

STOP!
If you have any problems with this product, please contact our technical support team for assistance.

TECHNICAL SUPPORT
Customer Service: 888-988-0488
Technical Support: 888-689-4088
Email: service@j5create.com
Service Hours: Mon. - Fri. 10:00 - 18:00 E.S.T

USB-C and USB are trademarks of USB Implementers Forum, Inc., its affiliates or its respective owners, registered or used in many jurisdictions worldwide. HDMI is a trademark of HDMI Licensing Administrator, Inc., its affiliates or its respective owners, registered or used in many jurisdictions worldwide. Windows is a trademark of Microsoft Corp., its affiliates or its respective owners, registered or used in many jurisdictions worldwide. macOS, iPadOS, and Airplay are trademarks of Apple Inc., its affiliates or its respective owners, registered or used in many jurisdictions worldwide. Android is a trademark of Google LLC, its affiliates or its respective owners, registered or used in many jurisdictions worldwide. DP is a trademark of Video Electronics Standards Association, its affiliates or its respective owners, registered or used in many jurisdictions worldwide. WiFi and Miracast are trademarks of Wi-Fi Alliance, its affiliates or its respective owners, registered or used in many jurisdictions worldwide. Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and/or names or their products and are the property of their respective owners. All company, product and service names used are for identification purposes only. Use of these names, logos, and brands does not imply endorsement. We disclaim any interest in the marks of others.