Related Manuals for BATTERIES PLUS X2 POWER SLC10002A
Summary of Contents for BATTERIES PLUS X2 POWER SLC10002A
- Page 1 SLC10002A INSTRUCTION MANUAL AUTOMATIC BATTERY CHARGER AUTOMATIC BATTERY CHARGER 0.8A BATTERIES PLUS ® EXCLUSIVELY AT...
- Page 2 Input: 110-120V AC 60 Hz 0.3A Output: 12V DC 0.8A 6V DC 0.8A 12.8V DC 0.8A AUTOMATIC BATTERY CHARGER Charges: 1 - 6/12V Lead Acid Flooded, Gel, Maintenance-Free, AGM Batteries 2Ah - 26Ah 1 - 12.8V Lithium Iron Phosphate (LiFePO4) 2Ah-15Ah Thank you for purchasing our product.
- Page 3 4. Operate charger only in well-ventilated areas. reassembly may result in a risk of electric Batteries generate explosive gases during shock or fire. normal operation. 12. Unplug the charger from power source before 5. Wear eye protection when operating charger. attempting any maintenance or cleaning.
-
Page 4: Safety And Precautions
intend to use in the vicinity of the battery. 6. Remove all jewelry and other metallic items Review cautionary marking on these from your hands and body when working products and on engine. with batteries. Metal may spark or create a short circuit resulting in electrical shock, fi re SAFETY &... -
Page 5: Charging Modes
LOCATION Locate the charger as far away from the battery as possible. Do not place the charger directly above the battery as gases from battery will corrode and damage charger. Do not allow battery acid to come in contact with charger. Do not operate the charger in a closed-in area or an area with restricted ventilation. - Page 6 Do not operate the charger until you confirm the appropriate charge mode for your battery. Here is a brief description. CHARGING MODES BATTERY VOLTAGE MODE DESCRIPTION OUTPUT SIZE For charging 12-volt Flooded, Gel, Normal 14.5V / 0.8A 2Ah-26Ah Maintenance-Free batteries. For charging 6-volt Flooded, Gel, Normal Maintenance-Free batteries.
- Page 7 CONNECTING TO BATTERY see (6). If positive post is grounded to the chassis, see (7). 1. Set any charger switches to “off” position and remove AC cord from electric outlet 6. For Negative-grounded vehicle, connect before connecting or disconnecting DC POSITIVE (RED) clamp or eyelet connector output clamps or eyelets.
-
Page 8: Preparing To Charge
CHARGING TIMES BATTERY SIZE (AH) 12V/6V APPROX. CHARGE TIME (HOURS) PREPARING TO CHARGE 1. If necessary to remove battery from vehicle 4. Study all battery manufacturer’s specific to charge, always remove grounded terminal precautions while charging and from battery first. Make sure all accessories recommended rates of charge. -
Page 9: Starting The Charging Process
THE BATTERY CHARGER MUST BE CONNECTED TO THE BATTERY ACCORDING TO THE INSTRUCTIONS ABOVE. STARTING THE CHARGING PROCESS: Once you have established that the battery clamps or eyelets have been correctly connected, you can start the charging process. To do so, insert the charger plug into the AC socket. The charger will start in Stand by mode, indicated by the AUTOMATIC BATTERY CHARGER STAND BY LED (1). - Page 10 STATE OF CHARGE INDICATORS The state-of-charge (SOC) LED display has four (4) SOC indicators. EXPLANATION The LED will flash when the battery is less than 25% Red LED 25% charged. When the battery is 25% charged, the LED will be solid. The LED will flash when the battery is less 50% Orange LED than 50% charged.
-
Page 11: Troubleshooting
TROUBLESHOOTING Error conditions are indicated in the LED display. ERROR REASON/SOLUTION Standard Charging The battery is not accepting a charge. Mode Change charge mode to Recovery Mode. Solid Red LED Recovery Mode The battery cannot be recovered. Battery capacity may be too high for the selected mode. Flashing Yellow LED Verify the battery capacity and charge mode. - Page 12 For warranty service, call 1-888-9-ASCENT. This warranty gives you specific legal rights, and you may also have other rights, which may vary from state to state. batteriesplus.com Replacement and recycling at Batteries Plus ® Distributed by Ascent Battery Supply, LLC.