Advertisement
6) Keystone commands
The keystone commands are used for the keystone setting of this projector with the value. The value will vary
depending on the installation conditions, etc.)
ITEM
KEYSTONE(vertical)
How to set the value
Use the ASCII or HEX code as shown below to set the value.
ASCII
'+'
'–'
HEX
2Bh
2Dh
7) Mute commands
is being displayed, the splash screen is only canceled.)
The mute commands are used for the mute setting of this projector with the 0 (30h) and 1 (31h).
ITEM
MUTE
8) Remote commands
screen is being displayed, the splash screen is only canceled.)
Some remote control operations can be achieved by the remote command codes. The remote commands have no data codes.
Button's name on remote
+ VOLUME
– VOLUME
KEYSTONE
MAGNIFY
AV MUTE
▲
▼
t
s
MENU
ENTER
AUTO POSITION
FREEZE
ASPECT
[Example]
When displaying the MENU selection bar (Figures and symbols enclosed in quotation marks are ASCII
codes.):
Sending commands
from the PC, etc.
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
'
9) Password lock commands
The password lock commands control the password lock. The password lock enabling or disabling command is sent
with a 4 to 8-digit password comprised of any figures 1 to 4 added to the end of the data code. When the password
lock is enabled or disabled successfully, the projector sends a return command comprising the data code,
password, and "1" at the end. When enabling or disabling the password lock fails, it sends a return command with
"0" at the end. There is no reconfirmation of the password. The password input command is for enabling projection
of image when password lock has been set to DISPLAY INPUT. The password input command is sent with a 4 to 8-
digit password comprised of any figures 1 to 4 at the end.
ITEM
Password lock
enabling/disabling
Password input
**** is a 4 to 8-digit password comprised of any figures 1 to 4.
(Not executable in stand-by mode. Possible only to read during muting.)
ASCII
HEX
KS
4Bh
53h
'0'
'1'
'2'
'3'
30h
31h
32h
33h
(Not executable in stand-by mode. When the mute commands are sent while the splash screen
ASCII
HEX
MUTE
4Dh
55h
(Not executable in stand-by mode. When the remote commands are sent while the splash
ASCII
HEX
r06
72h
r07
72h
r43
72h
r02
72h
ra6
72h
r53
72h
r2b
72h
r4f
72h
r59
72h
r54
72h
r10
72h
r09
72h
ra4
72h
re2
72h
Status code from
the projector
30 30 72 35 34 0D
'0' '0' 'r' '5' '4' '
ASCII
HEX
PSLOCK
50h
53h
PASS
50h
41h
VALUE
±20
'4'
'5'
'6'
'7'
34h
35h
36h
37h
VALUE
0 (OFF), 1 (ON)
54h
45h
30h
36h
30h
37h
34h
33h
30h
32h
61h
36h
35h
33h
32h
62h
34h
66h
35h
39h
35h
34h
31h
30h
30h
39h
61h
34h
65h
32h
'
4Ch
4Fh
43h
4Bh
53h
53h
3
'8'
'9'
38h
39h
Description
Command operating the same
as the MENU button
Command receipt confirmation
(Command echo back)
VALUE
0**** (Disabling), 1**** (DISPLAY INPUT),
2**** (MENU ACCESS), 3**** (SPLASH ID SCREEN)
****
Advertisement
