Page 2
READING THIS MANUAL IS MANDATORY BEFORE OPERATING THIS EQUIPMENT IMPORTANT THIS EQUIPMENT MAY BE SUBJECT TO DIFFERENT LAWS IN SOME PROVINCES, STATES OR COUNTRIES. THE USER MUST KNOW LAWS AND RULES GOVERNING TRANSPORTATION USE OF THIS EQUIPMENT ON PUBLIC ROADS. OWNERSHIP OF THIS EQUIPMENT DOES NOT CREATE SKILLS, OR ABILITIES TO OPERATE THIS EQUIPMENT.
1. TECHNICAL SHEET 1.1 DESCRIPTION Industrial snow plow with hydraulic wings and angle.The MaxxPro is installed on a wheel loader. LIVE EDGE SOFT DRIVE TRIP EDGE Available in HD, LE or RB-LE Includes angular system and quick coupler for industrial loader.
RB-LE - Rubber LIVE EDGE Individual floating rubber edge contouring the unevenness of the ground for a cleaner result while protecting delicate surfaces. RB-LE LIVE EDGE SOFT DRIVE TRIP EDGE RUBBER LIVE EDGE MAXXPRO...
2. INTRODUCTION The user must take note of the following information that may change the nature of the agreement between the manufacturer and the owner of the equipment. 2.1 NO MODIFICATION In no event shall this equipment be changed without the agreement of the manufacturer.
3. WARRANTY POLICY on new METAL PLESS equipment. METAL PLESS offers a warranty on all new equipment for a period of 1 year after date of retail purchase. AN APPROVAL FROM METAL PLESS IS REQUIRED BEFORE ANY REPAIRS OR WARRANTY CLAIMS.
4. USAGE OF THE EQUIPMENT & COMPONENTS PRESCRIBED USE (S) This equipment must be connected to a motorized vehicle and used for outdoor snow removal and to accomplish the following operations: a) Push snow forward. b) Backdrag snow. c) Windrow snow left or right. * Always wear a seat belt when operating a motor vehicle.
A permanent label shown in indicates the model number and the serial number. PRO 1048 AGH1036 - 16LE - 1610 - 1234 Width of # Production LIVE EDGE, mouldboard HD or RB-LE Model Height Total width Year and month of manufacturing Fig.1 MAXXPRO...
6. INITIAL ASSEMBLY Upon initial receipt of the equipment, some assembly may be required, check the following: 6.1 HYDRAULIC HOSES The equipment may require additional hydraulic hoses from the vehicle to the snow plow. It is the responsibility of the user to supply these. Hydraulic hoses must be routed and positioned in a way that they do not bind with mobile parts of the equip- ment.
It is not recommended to adjust these without prior approval from Metal Pless. If adjustment is necessary, note that both ports of the relief valve must be adjusted simultaneously for proper pressure relief of oil flow in either direction.
Page 12
MaxxPro as well as a few PlowMaxx models. To know the type of valve that is installed on your Metal Pless equipment, simply locate the labels on the hydraulic hases near the valve on the center of the plow that indicate the pressure and hydraulic flow li mit.
The usage of this equipment on another motorized equipment changes the behavior, conduct and balance; requiring professional expertise recognition. During the operation of this equipment, the user must maintain a safe distance between the equipment and it’s environment. The higher the speed, the higher the risks. MAXXPRO...
Page 14
WARNING SNOW EJECTS AT GREAT SPEED AND DISTANCES, AND CAN CREATE HARMFUL IMPACTS. DURING OPERATION, THIS EQUIPMENT CAN CAUSE THE VEHICLE TO BECOME UNBALANCED AND CAUSE A LOSS OF CONTROL. The user should consider that the use of this equipment reduces its overall vision and that the operator must therefore be vigilant.
30 jours (sauf pour les matières premières). La garantie de Sérigraphie Élite se limite à remplacer les autocollants défectueux, s’il y a lieu. Sérigraphie Élite aucune garantie de durabilité des impressions sur les matériaux fournis par le client. Les taxes applicables sont en supplément. 04-09-2020 DÉLAI DE LIVRAISON: 10 JOURS OUVRABLES. MAXXPRO...
8. FUNCTIONS AND OPERATIONS 8.1 LEVELLING THE PLOW In order to operate the equipment properly and also in order to avoid premature wear of this equipment, it is imperative that the plow is level and square to the (Fig. 3) ground during operations.
: Hydraulic wings may come in contact with the tires of the vehicle it is attached to. The operator must exercise caution and adjust the position of the wings to prevent them from coming in contact with the tires. Metal Pless shall not be liable for any damages caused to tires.
8.3 COIL SPRINGS Coil springs are installed on each side wing of this equipment, as shown below. Such coil springs allow limited movement of the abrasion shoe while maintaining down pressure onto the ground. (Fig. Coil Springs for HD or LIVE EDGE Hydraulic wings Fig.5 WARNING EXCESSIVE PRESSURE ON THE SNOW PLOW...
A trained operator will use the appropriate amount of pressure. Too much pressure will lead to premature wear. The maximal wear point is indicated by a groove cut into the cutting edges. (Fig. 8) MAXXPRO...
8.7 CUTTING EDGES (REPLACEMENT) On HD models, it will be necessary to replace the abrasion shoes on the wings at the (Fig.8) same time as the replacement of the main cutting edges of the blade. On live edge models, it is common to replace only the abrasion shoes multiple times prior to requiring the replacement of the live edge sections on the main blade.
8.9 FIFTH WHEEL This equipment has a mechanical system of limited lateral float (fifth wheel) allowing oscillation of the snowplow over uneven ground. The MaxxPro model is preset and does not need any adjustment. (Fig.9) On some models, chains are attached from the adapter plate to the tubular beam above the A frame to prevent the blade from over-oscillating when it is lifted and in travel mode.
9. MAINTENANCE 9.1 PRIOR NOTICE Unless otherwise stated, all maintenance requires that the equipment be placed on the ground. The use of safety stands are mandatory when servicing the equipment. RESPECT SAFETY INSTRUCTIONS AND ALWAYS USE APPROVED TOOLS. WARNING NEVER STAND OR STAND BETWEEN THE EQUIPMENT AND THE GROUND IF THIS EQUIPMENT HAS NOT BEEN PROPERLY SECURED WITH THE SUPPORT PROVIDED FOR THIS TASK.
9.5 LUBRIFICATION POINTS Periodic greasing All cylinder hinges All cylinder hinges MAXXPRO...
Page 24
MAXXPRO VIDEO ONLINE SCAN ME with your camera application on any phone WARNING WARNING: METAL PLESS SHALL NOT BE HELD LIABLE FOR ANY DAMAGE OCCURRED BY THE USE OF THIS EQUIPMENT. metalpless.com P: 819 362.2221 1 866.362.1688 F: 819 362.6974 info@metalpless.com...
Need help?
Do you have a question about the MAXXPRO and is the answer not in the manual?
Questions and answers