Advertisement
Quick Links
INSTALLATION - OPERATION - MAINTENANCE
24" MODELS
‰ R-R4
‰ R-R2G-12
‰ R-RG24
44 Lakeside Avenue, Burlington, Vermont 05401 USA
Telephone: (802) 658-6600 Fax: (802) 864-0183
www.mfii.com
R SERIES
HEAVY DUTY RANGES
36" MODELS
‰ R-R6
‰ R-R4G-12
‰ R-R2G24
‰ R-RG36
‰ R-R4RG12
© 2014 - Market Forge Industries Inc.
48" MODELS
‰ R-R8
‰ R-RG12-6
‰ R-RG24-4
‰ R-RG36-2
‰ R-RG48
‰ R-RRG24-4
60" MODELS
‰ R-R10
‰ R-RG12-8
‰ R-RG24-6
‰ R-RG36-4
‰ R-RG48-2
‰ R-RG60
‰ R-RRG24-6
PN 14-0400 Rev A (9/14)
Advertisement
Related Manuals for Market Forge Industries R Series
Summary of Contents for Market Forge Industries R Series
- Page 1 ‰ R-RG36-4 ‰ R-R4RG12 ‰ R-RG48 ‰ R-RG48-2 ‰ R-RRG24-4 ‰ R-RG60 ‰ R-RRG24-6 44 Lakeside Avenue, Burlington, Vermont 05401 USA Telephone: (802) 658-6600 Fax: (802) 864-0183 www.mfii.com PN 14-0400 Rev A (9/14) © 2014 - Market Forge Industries Inc.
- Page 2 Your Service Agency’s Address: Model Serial number Oven installed by Installation checked by...
-
Page 3: Table Of Contents
TABLE OF CONTENTS IMPORTANT WARNING: Improper installa- INSTALLATION tion, adjustment, alternation, Introduction ............. . 2 service or maintenance can cause property damage, in- Location . -
Page 4: Introduction
Introduction IMPORTANT INFORMATION SERVICE Safe and satisfactory operation of your equipment de- Installation of the equipment should be performed by pends on proper installation. Installation must conform qualified, certified, licensed and/or authorized personnel with local codes, or in the absence of local codes, the Na- who are familiar with and experienced in state/local instal- tional Fuel Gas Code, (ANSI Z-223.1 Latest Edition). -
Page 5: Location
Location READ BEFORE INSTALLING LEVELING A carpenter’s spirit level should be placed on the oven’s CLEARANCE center baking rack and the unit leveled both front-to-back When installing against combustible surfaces; rear - 4” and side-to-side. If it is not level, cakes, casseroles, and (102mm) and sides - 15”... -
Page 6: Dimensions And Burner Options
Dimensions and Burner Options Figure 1 INSTALLATION... -
Page 7: Utility Connections
Utility Connections ELECTRICAL CONNECTION shows gas flow direction; it should point downstream to the appliance. The red air vent cap on the top regulator is Oven requires a 120 volt supply to operate the ignition part of the regulator and should not be removed. system and blower. - Page 8 Utility Connections DISCLAIMER WARNING All MARKET FORGE INDUSTRIES, INC. appliances are DO NOT USE APPLIANCE DURING PRO- adjusted and tested before leaving the factory, effectively LONGED POWER FAILURE AS THE VENT matching them to sea level conditions. Adjustments and HOOD MAY NOT BE IN OPERATION RESULT-...
-
Page 9: High Shelf Assembly
High Shelf Assembly 1. Mount the back guard/ flue riser to the range with #10 NOTE: An authorized Service Personnel should install sheet metal screws (12 total) in the back. these items. If a Salamander /Broiler or Chee- seMelter/Broiler is to be mounted on range, read 2. -
Page 10: Operation
Operating Instructions Standard Oven WARNING Pilot gas is tapped from the main burner manifold pipe, Before lighting any pilots, make sure that routed through tubing to a pilot safety valve, and then to burner valves and thermostats are turned the pilot burner. Gas flow is controlled by the safety valve. “off”. -
Page 11: Lowed In The Event The User Smells Gas Must Be Maintenance Posted In A Prominent Lo- Cleaning & Periodic Maintenance
Cleaning & Periodic Maintenance PERIODIC CLEANING If the appliance is on casters and is connected to the supply piping by means of a connector for movable appli- Remove burner and clean with warm water and wire ances, there is a restraining device at the rear of the unit. brush.
Need help?
Do you have a question about the R Series and is the answer not in the manual?
Questions and answers