Advertisement
Quick Links
SPARTAK ENTERPRISES, INC.
RACKS-N-CABINETS
SWIVEL MEDIA TOWER
Model #2393-60DW
LOT #2780
IF PARTS ARE MISSING AND OR DEFECTIVE, IF INSTRUCTIONS ARE NOT CLEAR
OR IF YOU ARE EXPERIENCING PROBLEMS ASSEMBLING OUR PRODUCT.
BEFORE YOU RETURN THE PRODUCT TO THE STORE,
PLEASE CALL US TOLL FREE FOR CUSTOMER SERVICE ASSISTANCE
(888) 777-8250
OR SEND US EMAIL AT
help@spartakent.com
help@racks-n-cabinets.com
PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU
SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 951/360-0610 FAX; 951/360-0775
RACKS-N-CABINETS. 11186 VENTURE DR. MIRA LOMA,CA 91752 TEL: 951-360-0610 FAX: 951-360-0775
Advertisement
Summary of Contents for RACKS-N-CABINETS 2393-60DW
- Page 1 OR SEND US EMAIL AT help@spartakent.com help@racks-n-cabinets.com PLEASE HAVE ITEM NUMBER READY, AND A REPRESENTATIVE WILL GLADLY ASSIST YOU SPARTAK ENTERPRISES, INC. 841 E. FRANCIS STR. ONTARIO, CA. 91761 TEL; 951/360-0610 FAX; 951/360-0775 RACKS-N-CABINETS. 11186 VENTURE DR. MIRA LOMA,CA 91752 TEL: 951-360-0610 FAX: 951-360-0775...
- Page 2 HARDWARE PART # DESCRIPTION CCPZXX CAMLOCK COVER CAP CAMLT12 CAMLOCK CAMBT16 BOLT BM25 BRACKET ANGLE SPE610BL EURO SCREW BPXX54 SHELF SUPPORT TRNTPL SWIVEL PLATE TRNTSC SWIVEL BOLT DOWW830 WOOD DOWEL TOOL REQUIRED PHILLIPS SCREWDRIVER HAMMER...
- Page 3 NOTE: FIRST MAKE SURE THAT YOU HAVE ALL OF THE PARTS LISTED ON THIS SHEET. IF YOU ARE MISSING ANY PIECE(S), DO NOT ASSEMBLE THE UNIT. INSTEAD, CALL OUR CUSTOMER SERVICE NUMBER AT: (888) 777-8250. WE WILL BE HAPPY TO ASSIST YOU. 2393A-Top 2393D-Divider 4pcs...
- Page 4 Do not tighten screw on the angle bracket all the way in this step. Leave it a bit loose until you attach part D in the next step. Then you will tighten the screws. CAMLT12 UNLOCKED POSITION Use small hole #6 from the left end.
- Page 5 Press part (D) in the groove of part (E). Make sure part (E) and (D) are aligned with each other on both ends and RED and BLUE marked ends are on the same side. If you experience difficulty in lining up boards E and D with the angle brackets, try the following: 1) loosen the screw on the angle bracket attached to board E, 2) line up angle bracket hole with board D and attach screw...
- Page 6 Top Side CAMBT16 DOWW830 TRNTSC TRNTPL...
- Page 7 Lock camlocks on panels E as you install them before you proceed to next one. Otherwise panels may fall over and cause damage. Make sure you have on top only RED marked ends of panels D & E Turn camlocks clockwise using flat (preferred) or phillips scrudriver until full stop(slightly over 1 2 a turn...
- Page 8 Install top first. Next install one shelf in the middle (hole#8) on each side to restrict movement of inside dividers D. Do not tap with hammer onto shelf supports, instead twist them when inserting in. Turn camlocks clockwise until full stop (slightly over 1 2 a turn to lock the bolt) BPBL54...