Advertisement
Quick Links
Advertisement
Summary of Contents for Bayside R100D
- Page 1 Product Manual Direct Drive Rotary Table Product Manual...
- Page 2 Direct Drive Rotary Table Product Manual Rev: 3.1 / 1001 P/N: 12197009 Please check www.baysidemotion.com for latest revisions.
-
Page 3: Table Of Contents
Product Manual Direct Drive Rotary Table Table Of Contents I. Introduction II. Packaging Uncrating III. Mechanical Specifications IV. Electrical Specifications General Motor Rotary Encoder V. Wiring Appendix Power Digital Drive drawing - B 10963053 Rev 1 Sensor Digital Drive drawing - B 10963050 Rev 1 27 Seaview Boulevard * Port Washington, NY 11050 * 516-484-5353 * Fax: 516-484-5496 baysidemotion.com... -
Page 4: Introduction
R150D Rotary Stages R200D Rotary Stages R300D Rotary Stages If there are any questions regarding the set up of your product, please feel free to contact Bayside Motion Group, Technical Services at (516)484-5353 for additional support II. Packaging The stage is packaged in a wooden crate/carton with high density foam padding to avoid any damage during transportation. -
Page 5: Mechanical Specifications
Mechanical Specifications III. Mechanical Specifications Dimensions MODEL NO. (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) R100D 11.2 R150D 14.0 R200D Performance Specifications MODEL AXIAL PERPENDICULAR CONT PEAK RADIAL AXIAL WOBBLE STAGE CAPACITY CAPACITY OUTPUT... -
Page 6: Electrical Specifications
Example: R=ROTARY MODEL DRIVE SERIES D=Direct Drive For easy installation, motor power and encoder, hall, limit cables can be purchased from Bayside Motion Group. To order cables, please contact Bayside Sales Department at 516-484-5353 Cables Length Power Cable Sensor Cable... - Page 7 CONSTANT CONSTANT RESISTANCE INDUCTANCE VOLTAGE VOLTAGE CONT PEAK (V/KRPM) (Nm/A) OHMS@ 25°C Amps Amps R100D 0.72 59.9 2.72 5 V @ 600 ma 11.4 15.5 5 V @ 600 ma R150D 3.72 10.5 5 V @ 600 ma R200D R300D...
-
Page 8: Rotary Encoder
All motor speed/torque curves are based on 25 deg C ambient with a winding temperature of 155 deg C, at stall. Ambient temperatures above 25 deg C will require derating. Consult Bayside Motion Group, Technical Services at (516) 484-5482, ext. 130 for application assistance. -
Page 9: Wiring
Wiring V. Wiring Sensor Signal Connector PIN ASSIGNMENTS 26-Pin “D” Sub-miniature high density Pin Number Name Function /ENCA Encoder Channel A ENCA Encoder Channel A /ENCB Encoder Channel B ENCB Encoder Channel B /INDEX Encoder Channel I INDEX Encoder Channel I +5VDC Power Supply for Encoder (600mA) Encoder Common Spare... - Page 10 Wiring POWER CONNECTOR PIN ASSIGNMENTS 15-Pin "D" Sub-miniature Pin Numbers Name Function 1, 2, 9, 10 PHASE U (X) Motor Power In 3, 4, 11, 12 PHASE V (Y) Motor Power In 5, 6, 13, 14 PHASE W (Z) Motor Power In 7, 8, 15 Chassis Ground Note: Power for Phases are split over multiple pins.
- Page 11 If the speed exceeds the maximum setting (see table), the over speed fault signal /OVSP_ISO will be active, and all 4-digits will show two blinking bars, but all output position signals will remain enabled. Model R100D R150D R200D R300D Speed Limit...
Need help?
Do you have a question about the R100D and is the answer not in the manual?
Questions and answers