Page 2
PMC05ProSL-E 04.7.13 11:22 AM ページ 2 OWNER'S MANUAL...
Page 3
PMC05ProSL-E 04.7.13 11:22 AM ページ 3 CONGRATULATIONS! Thank you for purchasing the Vestax PMC05ProSL Mixing Controller. We suggest that you read through this owner's manual thoroughly so that you may enjoy the full use of this product safety and in the knowledge of all its special features and suitably applications. CONTENTS N 2 IMPORTANT SAFEGUARDS 3 F E A T U R E S 4 ...
PMC05ProSL-E 04.7.13 11:22 AM ページ 4 IMPORTANT SAFEGUARDS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. 1.Read instructions-All the safety and operating 9.This product should never be placed near or instructions should be read before the over a radiator or heat register. This product appliance is operated. should not be placed in a built-in installation such ...
Page 5
PMC05ProSL-E 04.7.13 11:22 AM ページ 5 15.Damage Requiring Service-Unplug this 16.Replacement Parts-When replacement product from the wall outlet and refer parts are required, be sure the service servicing to qualified service personnel under technician has used replacement parts the following conditions: specified by the manufacturer or have the ...
PMC05ProSL-E 04.7.13 11:22 AM ページ 6 FUNCTIONS TOP PANEL SECTION ent ice rts the rts. ire, ny ice to per be is uld ive the TRIM (PGM1/PGM2) PGM BALANCE (PGM1/PGM2) This pot adjusts the input level of each PGM This pot adjusts the stereo balance level for channel. ...
Page 7
PMC05ProSL-E 04.7.13 11:22 AM ページ 7 an IF-05PCV when it will worn out. For more CROSSFADER REVERSE SWITCH comprehensive instructions please refer to the This switch reverses the action of the crossfader "HOW TO CHANGE THE FADER UNIT" section by switching PGM1 and 2. of this user guide. PGM EFFECT (program effect) SWITCH It is the switch which sends the signal of each ...
Page 8
PMC05ProSL-E 04.7.13 11:22 AM ページ 8 SAMPLER/DELAY SECTION ore FEEDBACK the It is the volume which adjusts the amount of tion feedbacks (time of repeat). The number of times becomes 1 time when the pot turned to the left, and the number of times increases when the pot turns to the right. Notes When SAMPLER/DELAY SELECT switch is set up to other than DELAY mode, it dose not work.
PMC05ProSL-E 04.7.13 11:22 AM ページ 9 MIX VOLUME LEVEL/PLAY VOLUME It is the volume which adjusts the master output It is the volume which adjusts the effect level of level of SAMPLER / DELAY. When you want to SAMPLER / DELAY. In the SAMPLER mode, monitor ...
REAR PANEL SECTION l of de, of tart POWER SERIAL NO. of MADE IN CHINA UNDER LICENCE ack OF VESTAX TOKYO, JAPAN OUTPUT INPUT - PGM 2 INPUT - PGM 1 rve LINE 2 LINE 1 of DC 15V nd FOOT SW...
Page 11
PMC05ProSL-E 04.7.13 11:22 AM ページ 11 HOW TO USE THE SAMPLER/DELAY Delay Please check before operation that sound has come out from a MIXER or the connected speaker. 1.Set it as DELAY mode SAMPLER/DELAY SELECT switch is set to a "DELAY" side. 2. Set up delay time Strike TAP switch several times, listening to music source if you want to set delay by the speaker or headphone. (At this time, the button blinks according to the tempo that the button struck.) 3. Choose the channel to which an effect is applied ...
PMC05ProSL-E 04.7.13 11:22 AM ページ 12 SAMPLER NORMAL RECORDING 1. Set it as SAMPLER mode. Y" SAMPLER/DELAY SELECT switch is set to a "PRE-I.F" or"PRE-C.F"side. You can record the signal passed before inputfader on PRE-I.F,and the signal passed before crossfader on PRE C.F. 2. Select the channel to record rce Please push PGM EFFECT switch of the channel (PGM-1 (At ...
Page 13
PMC05ProSL-E 04.7.13 11:22 AM ページ 13 OVER DUBBING ■H 1.Turn on loop playback mode ① Push LOOP switch and set to loop playback mode. (Please check that the LOOP indicator is on at this time.) ② ③ 2. Start loop playback LEVEL/PLAY volume is raised and playback is started. fig. 3. Select the channel to record Push ...
PMC05ProSL-E 04.7.13 11:22 AM ページ 14 HOW TO CHANGE THE FADER UNIT ■How to remove a top panel ①As shown in fig-a, please remove the knob of INPUT LEVEL volume,CROSS FADER volume, MONITOR- de. LEVEL volume, C.F.MONITOR volume, and LEVEL / .) PLAY volume.(A total of six pieces) ②As shown in fig-a, please use a plus screwdriver (size: No.1), and remove the screw of four points which is fixing the top panel. ③As shown in fig-b, please remove the screw of two points ...
Page 15
PMC05ProSL-E 04.7.13 11:22 AM ページ 15 How to change input select switch ①remove the top panel in the same procedure. ③Carefully remove the multi cable connector from the ②Remove the two screws which fix the switch panel, fix switch unit(See fig-f) the switch panel, and remove the switch unit from ④Attach multicable connector to new switch unit. position in mixer.(See fig-e) ⑤Position the switch unit carefully, and the secure with the screws. How to change the direction of the switch ①remove the top panel in the same procedure. ...