Do you have a question about the W200 and is the answer not in the manual?
Questions and answers
Sumaira Irfan
February 6, 2025
My vacuum brush is not rolling
1 comments:
Mr. Anderson
February 10, 2025
The PRETTYCARE W200 vacuum does not have a brush roll, as mentioned in the context. The user noted that this model "really doesn't have a brush roll," which explains why the brush is not rolling.
This answer is automatically generated
Rosemary McGuire
June 1, 2025
What are the “error codes “ for prettycare model W200
1 comments:
Rosemary McGuire
June 1, 2025
@Rosemary McGuire Do you have a list of the error codes for this model ?
Philip Howell
May 26, 2025
The vacuum will charge to 100%, but will only run for 3 minutes.
1 comments:
Mr. Anderson
May 26, 2025
The PRETTYCARE W200 vacuum may only run for 3 minutes after charging to 100% due to a battery issue. Possible causes include:
1. A degraded or faulty battery that cannot hold a full charge. 2. Battery calibration issues causing the display to show 100% when it's not fully charged. 3. A malfunction in the power management system or internal electronics. 4. Using the vacuum continuously on high power, which significantly reduces runtime.
Normal runtime on high power is about 30 minutes, so 3 minutes indicates a potential defect.
This answer is automatically generated
Florence Harris
May 22, 2025
My prettycare 06/20/24 red with the round back won’t come on it would just stay on for a few minutes and go off
1 comments:
Mr. Anderson
May 25, 2025
If the PRETTYCARE W200 device turns on for a few minutes and then shuts off, a possible issue could be a low battery. In the context, the battery level was initially at 9% and later jumped to 59%, suggesting irregular charging or inaccurate battery reading. The device may shut off automatically if the battery is too low to maintain operation.
This answer is automatically generated
Rebecca Langston
April 12, 2025
Vacuum stopped working and two blue lights are blinking on top
1 comments:
Mr. Anderson
May 14, 2025
If the PRETTYCARE W200 vacuum stopped working and two blue lights are blinking on top, it likely indicates a low battery or charging issue. Ensure the vacuum is fully charged by checking the charger connection and trying a different electrical outlet. If the issue continues, clean the filter and remove any debris or blockages.
This answer is automatically generated
Donna Wilcox
March 8, 2025
Lights an roller cut out about 5 seconds after starting
1 comments:
Mr. Anderson
May 14, 2025
The PRETTYCARE W200 lights and roller cutting out about 5 seconds after starting could be caused by a blocked suction inlet, a clogged brush roller with pet hair or debris, or an overheating issue. Check and clean the suction inlet and brush roller, and ensure proper ventilation to prevent overheating.
This answer is automatically generated
Christy Johnson
February 4, 2025
Vacuume doesn't charge charging lights do not come on just big red light blinks and have no power
1 comments:
Mr. Anderson
May 14, 2025
If your PRETTYCARE W200 vacuum won't charge and shows a blinking red light, you should:
1. Ensure the vacuum is fully charged by properly plugging the charger into a working electrical socket. 2. Try switching to a different electrical outlet to rule out socket issues. 3. Check if the charger is securely connected to both the wall outlet and the vacuum.
If the problem persists after these steps, it may indicate a deeper issue with the battery or charger.
This answer is automatically generated
Eleanor Sanford
January 17, 2025
I tried everything in the manual and it still won't start and no charge light
1 comments:
Mr. Anderson
May 14, 2025
If your PRETTYCARE W200 won't start and there is no charge light, follow these steps:
1. Make sure the charger is properly plugged into both the wall outlet and the vacuum. 2. Check if the charger is compatible—use only a charger that matches 27V 0.8A output. 3. Inspect the power cord and plug for any damage. 4. Try a different outlet to rule out power issues. 5. Let the device charge for a while, even if no lights appear. 6. If there is still no response, the battery or charger may be faulty and may need replacement.
This answer is automatically generated
J. Carlson
June 27, 2025
This model does have a brush roll. Manual states to remove hair but there is no hair to remove. So it should be “rolling “.
Need help?
Do you have a question about the W200 and is the answer not in the manual?
Questions and answers
My vacuum brush is not rolling
The PRETTYCARE W200 vacuum does not have a brush roll, as mentioned in the context. The user noted that this model "really doesn't have a brush roll," which explains why the brush is not rolling.
This answer is automatically generated
What are the “error codes “ for prettycare model W200
@Rosemary McGuire Do you have a list of the error codes for this model ?
The vacuum will charge to 100%, but will only run for 3 minutes.
The PRETTYCARE W200 vacuum may only run for 3 minutes after charging to 100% due to a battery issue. Possible causes include:
1. A degraded or faulty battery that cannot hold a full charge.
2. Battery calibration issues causing the display to show 100% when it's not fully charged.
3. A malfunction in the power management system or internal electronics.
4. Using the vacuum continuously on high power, which significantly reduces runtime.
Normal runtime on high power is about 30 minutes, so 3 minutes indicates a potential defect.
This answer is automatically generated
My prettycare 06/20/24 red with the round back won’t come on it would just stay on for a few minutes and go off
If the PRETTYCARE W200 device turns on for a few minutes and then shuts off, a possible issue could be a low battery. In the context, the battery level was initially at 9% and later jumped to 59%, suggesting irregular charging or inaccurate battery reading. The device may shut off automatically if the battery is too low to maintain operation.
This answer is automatically generated
Vacuum stopped working and two blue lights are blinking on top
If the PRETTYCARE W200 vacuum stopped working and two blue lights are blinking on top, it likely indicates a low battery or charging issue. Ensure the vacuum is fully charged by checking the charger connection and trying a different electrical outlet. If the issue continues, clean the filter and remove any debris or blockages.
This answer is automatically generated
Lights an roller cut out about 5 seconds after starting
The PRETTYCARE W200 lights and roller cutting out about 5 seconds after starting could be caused by a blocked suction inlet, a clogged brush roller with pet hair or debris, or an overheating issue. Check and clean the suction inlet and brush roller, and ensure proper ventilation to prevent overheating.
This answer is automatically generated
Vacuume doesn't charge charging lights do not come on just big red light blinks and have no power
If your PRETTYCARE W200 vacuum won't charge and shows a blinking red light, you should:
1. Ensure the vacuum is fully charged by properly plugging the charger into a working electrical socket.
2. Try switching to a different electrical outlet to rule out socket issues.
3. Check if the charger is securely connected to both the wall outlet and the vacuum.
If the problem persists after these steps, it may indicate a deeper issue with the battery or charger.
This answer is automatically generated
I tried everything in the manual and it still won't start and no charge light
If your PRETTYCARE W200 won't start and there is no charge light, follow these steps:
1. Make sure the charger is properly plugged into both the wall outlet and the vacuum.
2. Check if the charger is compatible—use only a charger that matches 27V 0.8A output.
3. Inspect the power cord and plug for any damage.
4. Try a different outlet to rule out power issues.
5. Let the device charge for a while, even if no lights appear.
6. If there is still no response, the battery or charger may be faulty and may need replacement.
This answer is automatically generated
This model does have a brush roll. Manual states to remove hair but there is no hair to remove. So it should be “rolling “.
how to change out battery