Advertisement
Bluetooth headset should be used with the compatible devices which support Bluetooth wireless technology. This allows you to make two calls and enjoy the music streaming at any time freely. Please read this user manual carefully before using the headset, and also read your device's user manual regarding the Bluetooth function, and pay attention to those important safety and maintenance information.
Please keep the headset away from children.
Bluetooth Version: V5.0
Bluetooth Profiles Supported: HFP, HSP, A2DP, AVRCP
Audio Decoding Protocol: SBC AAC
Transmission Power: Class 2
Operation Range: Up to 10 meters
Frequency Range: 2.4GHz-2.48GHz
Battery of Headset: 45mAH Li-polymer Battery
Charging Voltage of Headset: 5V±0.2V
Charging Time of Headset: About 1.5 hours
Battery of Base: 420mAH Li-polymer Battery
Charging Voltage of Base: 5V±0.2V
Charging Time of Base: About 2hours
Charging Headset Times from Charging Base: 2-3 times
Music Playing Time: ≥ 6 hours
Talk Time: ≥ 6.5 hours
Standby Time: About 100 hours
Driver: φ6mm
Driver sensitivity: 90±3dB
Driver impedance: 16Ω±15%
Driver frequency ring range: 20HZ-20kHz
Dimensions of Charging Base(mm): L80×W33×H33
Dimensions of Headset(mm): L26×W16.6×H24.8
Weight(one headset): About 4.6g
Total Weight: About 42g
*The time mentioned above may vary due to user's operation mode and device settings.
Status No. | Status | Charging Base Performance |
1 | The Single Pairing headset(R) | The indicator light of headset(R) flashes red and blue alternately |
2 | TWS Pairing Mode | After TWS pairing successful, the indicator light of right headset alternately flashing red and blue, when the right headset pairing successful with mobile phone, the indicator light flashes blue once every 5 seconds |
3 | Standby Mode | The indicator light of the headset flashes blue once every 5 seconds |
4 | Call Mode | When in a call, the indicator light of the head set flashes red every 5 seconds |
5 | Headset Charging Mode | The indicator light of the headset is red when being charged, and will turn off automatically after being fully charged |
6 | Power On State | The indicator light flashes blue for three times. |
7 | Power Off State | The indicator light flashes red for three times. |
8 | Low Voltage Alarm State | The indicator light flashes red once every 20 seconds |
Status No. | Status | Headset Performance |
1 | Charging Mode of the Charging Base |
|
2 | Charging Base Battery Indication | The indicator flashing red once every 5 seconds means 25% battery, twice means 50%, 3 times means 75% and 4 times means full battery(100%). |
Identify according to L&R and wear the headset (R) and headset (L) respectively
Erect headset and place them into the cochlea
Slightly rotate headset until it's firm
Make the headset to cochlear edge tightly
Put the headset (L) (R) to the corresponding position in the bottom of the charging base.
Use the USB charging cable to charge
The red will flash according times until the battery is up to the corresponding level and will be always on when it is fully charged,
Note 1: Check the charging device is suit to the headset or not.
Note 2: Use only the supplied charger to charge the headset, if use other device may violate the validation or the maintenance article of this product and may cause danger.
Note 3: Do not attempt to force open the built-in battery as this could damage the headset.
Note 4: A fully charged headset will lose its power automatically if left unused. It is recommended to charge the headset each three months.
Note 5: Do not leave the headset in a too hot or too cold condition (best between -10℃ and 50℃) which may affect the headset's operations although it is fully charged.
Note 6: Do not dispose of the headset into fire or water.
Pick up the headsets from the charging base to turn on automatically.
Put them back to power off and charge the headset.
In OFF MODE, press and hold headset(R) or headset(L) MFB for 2 seconds to turn on.
In ON MODE, press and hold headset(R) or headset(L) MFB for 5 seconds to turn off.
Pick up the two headsets from the charging base to power on and waiting about 10 seconds, the two headsets will enter auto-pairing mode. The two headsets connect with each other after few seconds, the headset (R) alternately flashing red and blue, and then open the phone's Bluetooth device to search "BS228GB".
Note: When the first time to pairing or after delete the pairing records, the headsets should be paired under 20cm unobstructed.
In OFF state, press MFB key for 2 seconds to power on and waiting about 10 seconds, the two headsets will enter auto-pairing mode. The two headsets connect with each other after few seconds, the headset (R) alternately flashing red and blue, and then open the phone's Bluetooth device to search "BS228GB".
Do as the above ways: 1 or 2, and it prompts "Connected" after TWS paired successfully: left headset prompts "Left connected" and right headset prompts "Right connected-pairing"
Cell phone begins to search for Bluetooth devices (see the user guide of your phone instructions), and select "BS228GB" from Bluetooth device list.
Note: When the headsets TWS pairing failures, short press the headset R and headset L to enter TWS pairing, then pair with phone.
Method 1: Press and hold MFB of headset(R) or headset(L) for 2 seconds to power on→wait for few seconds, the two headsets connect automatically→the headset(R) pairs with the mobile phone that has ever paired after few seconds →reconnected successfully.
Method 2: Pick up the headsets from charging base to power on→wait for few seconds, the two headsets connect automatically→the headset(R) pairs with the mobile phone that has ever paired after few seconds →reconnected successfully.
Note: The headset(R)(L) will prompt "Connected", left headset prompts "Left Connected", the right headset prompts "Right Connected".
When call incoming, short press MFB of headset (R) or headset (L) to answer the call; In call mode, short press MFB of headset (R) or headset (L) to end the call when you hear "Call End".
Press and hold MFB of headset(R) or headset(L) for 2 seconds to reject the call, the speaker prompts "Doo, Call Reject".
On standby mode or music playing state, short press the MFB of headset(L). (This function only supports phone with voice dialing function)
(Only support the mobile phone which has the function of handling two phones.)
When you are answering a call, there is another call coming:
Note:
All the above operations have to respect the precondition supported Bluetooth hands free profile V1.5 and Phones are holding function (Network services) from telecom.
In standby mode, shortly press MFB of headset(R) to play music.
On music playing state, shortly press MFB of headset(R) to PAUSE music.
In call mode or music playing mode, double click MFB of headset(R) to volume up; double click MFB of headset(L ) to volume down, once "Doo" can be heard from headset R/L when volume is up to maximum or minimum.
In music playing mode, long press MFB of headset(R) for 2 seconds to next song; long press MFB of headset(L) for 2 seconds to previous song.
In OFF mode, press MFB of headset(R) or headset(L) for 10 seconds (OFF MODE→On Mode (2 seconds)→Delete Pairing Records (10 seconds) until hearing "Doo" 3 times and indictors flash red and blue twice at the same time.
Trouble | Reasons | Solutions |
Can not turn on | low battery protection | Charging headsets for 1-2 hours |
Can not turn on by picking up the headset/No indicator light when headset being charged | Charging base low battery protection | Charging both the headsets and charging base for 1-2 hours |
No sounds after pairing | Wrong pairing | Pairing again |
The two headsets TWS pairing failure/TWS paired successful but can not find the headset(R) | Too many pairing records | Delete pairing records |
Charging base without indicator light when charging | DC power supply doesn't output power | Check whether the micro USB charging line is plugged well or not |
Headsets without indicator light when charging | The headsets couldn't being charged in charging base |
|
Turning off automatically | Low battery | Charging headset for 1-2 hours |
Headset echo | Volume is too loud or environment is noisy | Adjust the volume at phone Change a place |
Noise in call | Environmental interference caused or distance between headset and mobile is too far | Change a place or move the headset close to the mobile phone |
Low voice of the calling party | Wearing headset is wrong | Adjusting wearing position of headset |
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Thank you! Your question has been received!
Need Assistance?
Do you have a question about the BS228GB that isn't answered in the manual? Leave your question here.