Related Manuals for MODSTER XC6
Summary of Contents for MODSTER XC6
- Page 1 USER MANUAL/BETRIEBSANLEITUNG DOWN CANCEL POWER 6CH DIGIT AL PROPO RADIO CONTROL S YS TE M BIND...
- Page 2 MODSTER XC6 Manual Thank for purchasing our product, an ideal radio system for beginners experienced users alike. Read this manual carefully before operation in order to ensure your safety, and the safety of others or the safe operation of your system.
-
Page 3: Table Of Contents
MODSTER XC6 Manual Table of Content SAFETY Safety Symbols Safety Guide INTRODUCTION System Features Transmitter Overview 2.2.1 Transmitter Antenna 2.2.2 Battery lndicator 2.2.3 Trims Receiver Overview 2.3.1 Receiver Antenna 2.3.2 Connectors GETTING STARTED Transmitter Battery Installation Connecting the Receiver and Servos... - Page 4 MODSTER XC6 Manual Subtrim Dual rate/exp. Throttle Curve Mixes 5.10 Elevon 5.11 V Tail 5.12 Assign Switches 5.13 Throttle Hold HELICOPTER FUNCTIONS Pitch Curve Swashplate Mix Gyroscope SYSTEM Model Select Model Name Type Select Model Copy Model Reset Trainer Mode...
- Page 5 MODSTER XC6 Manual Output Mode i-BUS Setup 8.10 Servos Freq SYSTEM CUSTOMIZATION Switching Channel Assignments Activate Switch/Knob PACKAGE CONTENTS PRODUCT SPECIFICATION 11.1 Transmitter specification (MODSTER XC6) 11.2 Receiver specification (MODSTER XC6) www.modster.at...
-
Page 6: Safety
MODSTER XC6 Manual 1. Safety 1.1 Safety Symbols Pay close attention to the following symbols and their meanings. Failure follow these warnings could cause damage, injury death. Not following these instructions may lead to serious injuries or death. Danger Warning Not following these instructions may lead to major injuries. - Page 7 MODSTER XC6 Manual Misuse of this product may lead to serious injury or death. To ensure the safety of you and your equipment, read this manual and follow the instructions. Make sure the product is properly installed in your model. Failure to do so may result in serious injury.
-
Page 8: Introduction
MODSTER XC6 Manual 2. Introduction The FS-i6X transmitter and FS-iA6 receiver constitute a 6-channel 2.4GHz AFHDS 2A digital proportional computerized R/C system. lt is compatible with fixed-wing and helicopters. 2.1 System Features The AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) developed and... -
Page 9: Transmitter Overview
MODSTER XC6 Manual 2.2 Transmitter Overview www.modster.at... -
Page 10: Transmitter Antenna
MODSTER XC6 Manual 2.2.1 Transmitter Antenna For best signal quality, make sure that the antenna is at about a 90 degree Warning angle to the model. Do not point the antenna directly at the receiver. Never grip the transmitter antenna during operation. -
Page 11: Connectors
MODSTER XC6 Manual 2.3.2 Connectors The connectors are used to connect the parts of model and the receiver. CH6: used to connect the servos, power or other parts. B/VCC: used to connect the bind cable for binding and the power cable during normal operation. -
Page 12: Getting Started
MODSTER XC6 Manual 3. Getting Started Before operation, install the battery connect the system as instructed below. 3.1 Transmitter Battery Installation Danger Only use specified battery. Do not open, disassemble, or attempt to repair the battery. Danger Danger Do not crush/puncture the battery, or short the external Danger contacts. -
Page 13: Operation Instructions
MODSTER XC6 Manual 4. Operation Instructions After setting follow the instructions below to operate the system. 4.1 Power On Fellow the steps below to turn system: Check the system and make sure that: The batteries are fully charged and installed properly. -
Page 14: Pre-Use Check
MODSTER XC6 Manual 4.3 Pre-use Check Before operation, perform following steps to check system: Check make sure that all servos and motors are working as expected. Check operating distance: one operator holds the transmitter, and another one moves model away from the transmitter. -
Page 15: Power Off
MODSTER XC6 Manual When switching between modes one and two it is necessary to reverse the gimbals positions to ensure that throttle is on the correct side. To switch the sticks: Take the battery out from the transmitter, Loosen the four screws that hold the rear cover shown in green on left . -
Page 16: Function Descriptions
MODSTER XC6 Manual 5. Function Descriptions 5.1 Flight Controls (Default Mode 2) The sticks are used for controlling the aircraft, each stick has 2 functions The right stick controls pitch and roll, the left stick controls throttle and yaw. www.modster.at... -
Page 17: Reverse Function
MODSTER XC6 Manual 5.2 Reverse Function reverse function changes a channels direction of movement in relation to its input. For example, if a servo has to be mounted upside down due to space restrictions within a model, this function can be used to correct its movement so that it... -
Page 18: Display
MODSTER XC6 Manual 5.4 Display This function displays the model's channel output in real time. Make sure the model engine is powered off while the test function is activated. Warning If powered on, it will rev up and cause unexpected results. -
Page 19: Throttle Curve
MODSTER XC6 Manual rudder will move 2.5 cm, at 100% there is a direct, linear relationship of stick movement and surface movement. a setting of 50% is entered then moving the stick all the in one direction will only give 1/2 of the... -
Page 20: Elevon
MODSTER XC6 Manual Set the positive and negative mix, this setting controls how much the slave channel will move in relation to the masters movement, if to 50% the slave will move half the amount the master. Set the offset, the offset changes the center of the slave channel in relation to the master. -
Page 21: Throttle Hold
MODSTER XC6 Manual 5.13 Throttle Hold This function is used with gas powered models in order stop stalls when not in use. Setup: 1. Use the "OK" key to change between settings. Use the "UP" and "DOWN" keys to turn the function on or off and increase and decrease the hold percentage. -
Page 22: Gyroscope
MODSTER XC6 Manual 6.3 Gyroscope The gyroscope function uses a gyroscope to correct for torque produced changes in engine speed, pitch and wind etc., which can cause issues with control. If not corrected each of these variables could cause the RC helicopter to spin, sometimes quite violently. -
Page 23: Model Reset
MODSTER XC6 Manual Setup: Use the "UP" and "DOWN" keys to select the model you want to copy. Use the "OK" key to and use the "UP" and "DOWN" keys to select the slot to copy the model. 3. Press and hold the "OK"... -
Page 24: Firmware Version
MODSTER XC6 Manual To return to default settings press and hold the "OK" key for 3 seconds, press and hold the "CANCLE" key to save. 7.10 Firmware Version This function displays the current firmware version. 7.11 Firmware Update This function updates the firmware using a USB to PS/2 connection lead. -
Page 25: Rx Setup
MODSTER XC6 Manual 8. RX Setup 8.1 RF Standard This menu allows you to change the communication protocol for the transmitter. The available protocols are: RF Protocol Reiceiver AFHDS R9B,R6B,R6C,GR3E,GR3F AFHDS 2A A3, A6,X6, iA4B, iA6, iA6B, iAl0, iAl0B To Switching Between AFHDS 2A and AFHDS: First navigate to the system menu by pressing and holding the "OK"... -
Page 26: Sensors List
MODSTER XC6 Manual To return to default settings press and hold the "OK" key for 3 seconds, use the "UP" and "DOWN" keys to select Yes. press and hold the "CANCLE" key to save. You can the failsafe position for all channels with the [AII channels] button at once. -
Page 27: Asl Pressure
MODSTER XC6 Manual 8.7 ASL Pressure The set ASL (Above Sea Level) function is used to calibrate an altitude sensor. When an altitude sensor connected, change the [Air pressure] setting until the altitude is at 0m. Setup: 1. Make sure that your RX are bound and turned on. -
Page 28: System Customization
MODSTER XC6 Manual 9. System Customization The MODSTER XC-6 switches and knobs can be moved other channels. Or if using receivers with more channels, system can be expanded with extra switches or knobs. default, from left to right, the knobs are channels... - Page 29 MODSTER XC6 Manual 5. On the circuit board each channel is labeled, making it easy to find the correct channel. Follow the cables leading from each connector to identify which switch or knob goes to each channel. Carefully remove the desired connectors from the board.
-
Page 30: Activate Switch/Knob
MODSTER XC6 Manual 9.2 Activate Switch/Knob Open the system menu, navigate to "Aux Switches" and press the "OK" key. Use the "OK " key to change switch/knob, then use the "UP" or "DOWN" keys to turn the switch switch will now be available in the "Assign Switches"... -
Page 31: Product Specification
MODSTER XC6 Manual 11. Product Specification 11.1 Transmitter specification (MODSTER XC6) Channels 6-10 (Default 6) Model Type Fixed-Wing/Glider/Helicopter RF Range 2.408-2.475GHz RF power < 20dBm RF Channel Bandwidth 500KHz 2.4GHz System AFHDS 2A / AFDHS Modulation Type GFSK Stick Resolution... -
Page 32: Receiver Specification (Modster Xc6)
MODSTER XC6 Manual 11.2 Receiver specification (MODSTER XC6) Channels Model Type Fixed-Wing/Glider/Helicopter RF Range 2.408-2.475GHz RF Channel RF Receiver Sensitivity - 105dBm Bandwidth 500KHz 2.4GHz System AFHDS 2A Modulation Type GFSK Power 4.0~6.5V Antenna Length 26mm(Dual Antenna) Weight Size 40.4x21.lx15mm... - Page 33 MODSTER XC6 Manual Appendix 1 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules. These limits designed to provide reasonable protection against harmful interference in a residential installation.
- Page 34 Declaration of Conformity in accordance with the Radio Equipment Directive (RED) 2014/53/EU Déclaration de conformitè CE (RED) 2014/53/EU Hiermit wird erklärt, dass die Produkte: I hereby declare that the products: MODSTER XC6 6-Kanal Fernsteuerung inkl. MODSTER MR6 Empfänger Il est déclaré que les produits: Artikelnummer: Product number:...
- Page 35 MODSTER XC6 Manual www.modster.at...
Need help?
Do you have a question about the XC6 and is the answer not in the manual?
Questions and answers