ETI 564221430 Use And Care Manual

USE AND CARE GUIDE

10 IN. FLUSHMOUNT WITH PULL CHAIN

PACKAGE CONTENTS

Part Description Quantity
A Fixture Body 1

HARDWARE INCLUDED

Part Description Quantity
AA Mounting Bracket 1
Mounting Screw (for
BB 2
Bracket)
CC Wire Connector 3

NOTE: Keep your receipt and these instructions for proof of purchase.

WARNING: RISK OF ELECTRIC SHOCK. Ensure the electricity to the wires you are working on is shut off. Either remove the
fuse or turn off the circuit breaker before removing an existing light fixture or installing the new one.
If you are unfamiliar with electrical installations, we recommend you contact a qualified electrician to do the installation.

INSTALLATION

Select a suitable location that can support the weight of the fixture. Determine the method for mounting the fixture before
drilling, based on the type of ceiling.
1. Pass the hot and neutral (black and white) wires from the electrical outlet box through the middle hole of the mounting
bracket (AA).
Align the mounting bracket (AA) using the mounting screws (BB) and tighten securely to the electrical box.
2. Connect the hot and neutral (black and white) wires from the J-box to the same color wires from the fixture body (A).
Connect the grounding wire from the J-box to the green wire from fixture base (A). Cover the wire connections using the
wire connectors (CC). Make sure to fasten them well.
3. Cover the wire connectors (CC) with electrical tape for a more secure connection.
4. Position the wires back inside the electrical box.
5. Align the side slots on the fixture body (A) with the mounting bracket (AA) and fix the fixture body (A) securely by carefully
rotating in clockwise the side slots inside the mounting bracket (AA).
6. Restore power at the electrical panel. Pull the chain down to turn the light on and off.
STEP 1. STEP 2.
AA
BB
Model # 564221430
Part # FM-10IN-900LM-8-40K-SV
A
AA BB CC
STEP 3.
Side slot
AA
CC
A

CARE AND CLEANING

CAUTION: Before attempting to clean the tube and luminaire/light fixture, disconnect the power to the fixture by turning the
breaker off or removing the fuse from the fuse box. Clean with a soft, dry cloth. Do not use cleaners with chemicals, solvents, or
harsh abrasives. Do not use liquid cleaner on the LEDs, LED driver, or wiring.
WARNING: Carefully read and understand the information given in this manual before beginning the assembly and installation.
Failure to do so could lead to electric shock, fire, or other injuries which could be hazardous or even fatal. • Ensure the electricity to
the wires you are working on is shut off. Either remove the fuse or turn off the circuit breaker. • To reduce the possibility of serious
injury, always take the proper precautions and unplug the fixture before moving or cleaning. • Risk of fire or electric shock.
NOTICE: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures: Reorient or relocate the receiving antenna, increase the separation
between the equipment and the receiver, connect the equipment into an outlet on a circuit different from that to which the
receiver is connected, and consult the dealer or an experienced radio/TV.
• Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
See website for Warranty, Troubleshooting or Care and Cleaning details at www.ETiSSL.com.
Questions, problems, missing parts?
Call ETiSSL Customer Service 8 a.m. - 5 p.m., CST, Monday - Friday
1-855-ETI-SSLI (1-855-384-7754) www.ETiSSL.com