WattBox WB-800ICH1U-IPVM-8 Quick Start Manual
  1. Manuals
  2. Brands
  3. WattBox Manuals
  4. Accessories
  5. WB-800ICH1U-IPVM-8
  6. Quick start manual

WattBox WB-800ICH1U-IPVM-8 Quick Start Manual

Socket-outlet
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
WB-800ICH1U-IPVM-8
Quick Start Guide

Advertisement

Table of Contents
loading

Related Manuals for WattBox WB-800ICH1U-IPVM-8

Summary of Contents for WattBox WB-800ICH1U-IPVM-8

  • Page 1 WB-800ICH1U-IPVM-8 Quick Start Guide...

  • Page 2: Important Safety Instructions

    Important Safety Instructions Read and observe the following safety points at all times. Notice For indoor user only. Internal components are not sealed form the environment. The device can only be used in a fixed location such as a telecommunication centre, or a dedicated computer room. When you install the device, ensure that the protective earthing connection of the socket-outlet is verified by a skilled person.

  • Page 3: Package Contents

    Package Contents (1) WB-800ICH1U-IPVM-8 (4) Screw-in feet and screws (1) Removable, region-specific (1) IEC sleeve (2) Rack mounting brackets power cord (in over-pack box, not PDU carton) (8) Mounting bracket screws (1) Quick Start Guide (M3 x 6 mm)

  • Page 4: Rear Panel

    G. Safe Voltage button: Toggles the Safe Voltage feature on and off. When enabled, Safe Voltage turns off outlets to protect connected equipment from out-of-range input voltage. H. UPS Link: For future use to connect a WattBox OvrC-enabled UPS. ACC port: Accessory port for future use.

  • Page 5: Front Panel

    Front Panel A. AC Power button: Press and hold for 3 seconds to manually toggle the outlets on or off. Outlets configured as Disabled or Reset Only are not affected. B. LED indicators: See the status of the internet, Safe Voltage, surge protection, and whether the unit is properly grounded.
  • Page 6 The LED light flashes on the specified outlet for 5 minutes, during this time the display windows show the Current for the selected outlet. Once the 5 minutes has expired, the WattBox defaults back to displaying the aggregate total of the entire unit, and all LEDs default back to being illuminated.
  • Page 7 How to Manually Reset All Outlets from the Faceplate To reset all of the outlets, press and hold B1 and B2 at the same time for 3 seconds. The Current display shows a rotating 0 as the outlets reset. Note: The reset follows the Power-On delay set in OvrC.

  • Page 8: Led Operation

    Safe Voltage is disabled. Blue (Solid) The WattBox is powered on and outlets are protected. Surge The WattBox is not powered on, or the MOVs have opened, removing Protected power from the outlets. Blue (Solid) Incoming AC outlet is grounded.
  • Page 9 Positioning Options The WB-800ICH1U-IPVM-8 can be mounted in a rack or placed in a cabinet. Rack Mounting Attach mounting brackets to the WattBox using the supplied hardware, then install the WattBox into the rack using standard rack screws (not included).
  • Page 10 Cabinet Placement Attach supplied feet to the bottom of the WattBox for cabinet placement.

  • Page 11: Connections And Setup

    Connections and Setup Web Browser PROTECT PROTECT CLIP CLIP CH.SEL Access MENU SIGNAL SIGNAL ADJUST | SET EA-AMP-HYB-2D-1000 BACK Router Mobile WB-800ICH1U-IPVM8 Apps 1. For IP control and OvrC connectivity, connect a network cable from your router or switch into the WB-800I Network port.
  • Page 12 Claiming the WattBox on OvrC The WB-800I has many powerful features that are accessed through OvrC, our award-winning remote management tool. To get started with OvrC, visit OvrC.com. To find training for OvrC, go to snp1.co/ovrc. Completing OvrC Setup 1. Ensure the WB-800I is connected to the internet via your router or network switch.

  • Page 13: Troubleshooting

    Troubleshooting Symptom Possible Cause Remedy If the WattBox power button does not show blue, WattBox is not turned on. press it. Make sure the AC power plug is plugged into a properly grounded 220-240V (nominal) wall outlet. Some outlets are controlled by a wall switch. Try WattBox is not No power is being supplied.
  • Page 14 Symptom Possible Cause Remedy Component is plugged into a Log in to the WattBox interface to turn the outlet on. controlled outlet and the outlet is The attached Factory default the WattBox. off. component is not receiving In some instances, a component...

  • Page 15: Specifications

    Specifications Outlet Type IEC 60320 C13 Number of Outlets 9 total — 1 on front, 8 on back Number of IP Controllable Outlets Line Voltage 220–240VAC, 50/60Hz AC Input Connection IEC 60320 C14 Fuse Rating 10A, 250VAC Power Rating 2400W Voltage Protection Rating L-N 900 V, L-E 1.9 kV, N-E 1.7 Kv Joule Rating...
  • Page 16 Outlet Filter 1 bank with 8 outlets Operating Temperature Range -10 °C to 40 °C (−14 °F to 104 °F) Certifications CE/AU Dimensions (WxHxD) 440 mm (17.32") ×44 mm (1.73") ×312 mm (12.28")
  • Page 17 Dimensions...

  • Page 18: Logging Into The Web Interface

    One, LLC (formerly known as Wirepath Home Systems, LLC), in the United States and/or other countries. 4Store, 4Sight, Control4, Control4 My Home, SnapAV and WattBox are also registered trademarks or trademarks of Snap One, LLC. Other names and brands may be claimed as the property of their respective owners. Snap One makes no claim that the information contained herein covers all installation scenarios and contingencies, or product use risks.

Table of Contents