Page 1
6310 Application Ready Platform (SYS6310) User Guide P/N: Rev A December 13 2022...
Page 2
Purchase and Software License Agreement for the SDA450 based Inforce 6310 hardware, which you or the legal entity you represent, as the case may be, accepted and agreed to when purchasing a Inforce 6310 hardware from SMART Wireless Computing (“Agreement”). You may use this document, which shall be considered part of the defined term “Documentation”...
Page 3
Revision History Description Revision Date Author Initial Revision June 09 2021...
Use a grounded anti-static mat Use a grounded wrist or foot strap HARDWARE IDENTIFICATION LABELS Labels are present on the 6310 TM Application Ready Platform (SYS6310). The following information is conveyed on the 6310 TM Application Ready Platform (SYS6310): Serial Label ...
HARDWARE SPECIFICATION HARDWARE SPECIFICATION INTRODUCTION The 6310 Application Ready Platform (SYS6310) can be used to develop, test, and deploy end-user product solutions around Qualcomm Snapdragon SDA450 processor. SYSTEM SPECIFICATION The following table shows the hardware specification of the 6310TM Application Ready Platform (SYS6310)
6310 Application Ready Platform (SYS6310) User Guide HARDWARE SPECIFICATION ARCHITECTURE Figure 1: 6310 Application Ready Platform (SYS6310) Block Diagram P/N: Rev A MAY CONTAIN U.S. AND INTERNATIONAL EXPORT CONTROLLED INFORMATION Confidential and Proprietary. Provided under NDA...
6310 Application Ready Platform (SYS6310) User Guide HARDWARE SPECIFICATION Bluetooth Classic: 2402MHz - 2480MHz Blue tooth Cla ssic : 2402MHz - 2480MHz BLE: 2402MHz - 2480MHz BLE: 2402MHz - 2480MHz 2.4 GH z WI FI : 2.4 GH z WI FI :...
Page 9
6310 Application Ready Platform (SYS6310) User Guide HARDWARE SPECIFICATION Table 2: SYS6310 Application Ready Platform interface Locations Description DC Power Jack Micro-AB USB Connector (Debug) Micro HDMI Connector (Type D) Stacked USB 3.0 Type A Connector Ethernet - RJ45 Connector...
SYSTEM SETUP AND USAGE HARDWARE SETUP The Figure below shows the Hardware setup of 6310 Application Ready Platform (SYS6310) AC Mains Socket Power Adapter: 12VDC 2A Ethernet Cable Type A HDMI uUSB Dual USB Type DC Power RJ45 Jack HDMI...
HARDWARE OPERATION STEPS TO BOOT 6310 APPLICATION READY PLATFORM (SYS6310) Connect the DC power adaptor to the 6310 TM Application Ready Platform (SYS6310) Carefully connect the DC connector to the jack provided on the board. CAUTION Use 12V, 2A DC Adaptor.
Page 12
FASTBOOT MODE Follow the below steps to enter fast boot mode. 1. Connect 6310 TM Application Ready Platform (SYS6310) and host PC using a Micro USB cable 2. Power on the board. 3. Once the device is booted up, open the command prompt in the host PC and enter the following commands ...
COMPLIANCE DETAILS CLASS B PRODUCT COMPLIANCE STATEMENT Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
The 6310 is in compliance with the essential requirements and other relevant provisions of the RE Directive 2014/53/EU. b. This device is restricted to indoor use only when operating in the 5150 to 5350 MHz frequency range. c. A minimum separation distance 20cm is required.
Page 16
Penguin Solutions is a trade name used by SMART Wireless Computing, Inc., a wholly owned subsidiary of SMART Global Holdings, Inc. Penguin Edge is a trademark owned by Penguin Computing, Inc., a wholly owned subsidiary of SMART Global Holdings, Inc. Qualcomm and Snapdragon are trademarks of Qualcomm Incorporated, registered in the United States and other countries.