Advertisement
Quick Links
Value Gable Shed/Value Workshop Shed
ASSemBly InStruCtIOn mAnuAl
Value Gable Shed
Sizes: 8'x8', 8'x10', 8'x12', 8'x14', 8'x16', 10'x10', 10'x12', 10'x14',
10'x16, '10'x18', 10'x20, '12'x12', 12'x14', 12'x16', 12'x18', 12'x20', 12'x24'
tools needed:
- Cordless Drill (12 V Or Higher)
- #2 Square Drive Bit
- Hammer
- 6' Step Ladder
- Tape Measure
- Square Utility Knife With
Blade & Hook Blade
- Speed Square
PO Box 455, Berlin, OH 44610 • 330-893-4212 • www.cottagekits.com
Pre-Cut
LITTLE COTTAGE CO.
Value Workshop Shed
Items to Purchase:
- Shingles
- Drip Edge
- Paint
See the Kit Packing
List Included For
Quantities
© 2020 Little Cottage Co.
Advertisement
Related Manuals for Little Cottage Value Gable Shed
Summary of Contents for Little Cottage Value Gable Shed
- Page 1 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl Value Gable Shed Value Workshop Shed Sizes: 8’x8’, 8’x10’, 8’x12’, 8’x14’, 8’x16’, 10’x10’, 10’x12’, 10’x14’, 10’x16, ’10’x18’, 10’x20, ’12’x12’, 12’x14’, 12’x16’, 12’x18’, 12’x20’, 12’x24’ tools needed: Items to Purchase: - Cordless Drill (12 V Or Higher)
- Page 2 ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* thank you for purchasing from little Cottage Co.! Using the floor diagram layout sheet, locate your rim If you have any questions during construction please and floor joist and lay them out.
- Page 3 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Using the wall diagram layout sheet, locate the 2x4 To create the wall interior, fasten the 2x4 studs with 3”...
- Page 4 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Next make sure the top of the siding is flush with 2x4 Make sure the outside corners are flush as shown studs.
- Page 5 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* 19. Install the 2 3/4” trim around the door. Secure the Lay wall to side as shown.
- Page 6 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Continue with Smartside and fasten with 2” nails Lay wall to the side as every 6 to 8 inches.
- Page 7 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Secure the truss to the top plate with 3” nails. Locate the gable siding layout sheet. Install the Smartside making sure it is 3”...
- Page 8 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Make sure the small piece of Smart side is installed at For rake installation, measure 2” from the edge of the the top.
- Page 9 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Make sure the wall is flush on the end and put pressure Fasten with 3” nails 16” on center.
- Page 10 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Fasten with 2” nails. Make sure the walls are in place, and secure with 3”...
- Page 11 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Flip the truss around and do the same with the gusset. Locate the temporary wall braces. Note: Wall bracing Repeat with remaining trusses.
- Page 12 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Install the trusses as shown, making sure they are Install 2 3/4” trim as shown, keep flush with the 24”...
- Page 13 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* 68. Next install the drip edge as shown (drip edge not Make sure the trusses are 24” on center before fastening sheeting.
- Page 14 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Continue with starter strips. Install shingles in a staggered fashion. Continue with shingles as shown.
- Page 15 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Locate the window, shutters and trim. Install the window and fasten with 2” nails as shown.
- Page 16 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Install the door with 1 1/4” black headed screws, 3 Install the screws on the bottom.
- Page 17 Pre-Cut Value Gable Shed/Value Workshop Shed ASSemBly InStruCtIOn mAnuAl *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Drill a 5/16” hole as shown. Use the hammer again to tap on the top barrel bolt to locate where to drill your 5/16”...
- Page 18 *PleASe nOte: A 10’X14’ WOrKSHOP SHeD WAS uSeD FOr PICtureS SHOWn - yOur lAyOut mAy VAry* Colonial Williamsburg Garden Shed Completed Value Workshop Shed your Finished Product!!! thank you For Purchasing From little Cottage Co. enjOy! Completed Value Gable Shed Assembly Instruction manual...