1. Manuals
  2. Brands
  3. Spectec Manuals
  4. Industrial Equipment
  5. 4057 Series
  6. User manual

Spectec 4057 Series User Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
4057 SERIES USER GUIDE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 4057 Series and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Spectec 4057 Series

Summary of Contents for Spectec 4057 Series

  • Page 1 4057 SERIES USER GUIDE...

  • Page 2: Table Of Contents

    Contents DEVICE OVERVIEW .................................... 2 4057B P ......................................2 INOUT ......................................2 EFINITIONS LCD U .................................. 2 NTERFACE VERVIEW LCD SETUP MODE ....................................3 LCD S ..................................3 NTERING ETUP ......................................3 LCD S ..................................3 XITING ETUP ...................................... 3 ASSWORD NTRY ......................................

  • Page 3: Device Overview

    LCD Setup Mode: Configuration is done through the LCD using the selection dial (Figure 1). USB Setup Mode: Configuring the device is done by a file that is generated by the “4057 Series Configuration Software”. (Can be downloaded from Pin 10 our website.

  • Page 4: Lcd Setup Mode

    LCD Setup Mode Entering LCD Setup Mode Password Entry 1) Apply power to the 4057B. 1) When enabled you will be prompted for a 2) When you see “Push Button to Enter Setup” password (Figure 11) when entering LCD momentarily press down on the selection setup mode.

  • Page 5: Options Setup

    Options Setup Display: BackLite Factory Display* LCD time* Reset Figure 7: Display Options. Password Date/Time Figure 4: Options Menu. BackLite Setup: “Factory Reset” sets the unit back to After selecting BackLite you will see Figure factory defaults including the password. 8.
  • Page 6 1) To set up the timer select the appropriate DO NOT FORGET TO RECORD YOUR digit by rotating the selection dial and PASSWORD IN A SECURE LOCATION. IF highlighting the digit you want to change. YOU LOSE YOUR PASSWORD THE DEVICE 2) Momentarily press down on the selection WILL HAVE TO BE SENT BACK TO THE dial.

  • Page 7: Output Type Setup

    Output Type Setup Digital Output Setup (Hz Selection only) Hz rpm gpm BPH LPM LPH Multiply* Disable fps Mph m/s kph Divide K factor Figure 15: Digital Output (Hz). Figure 13: Output Type Menu. “Multiply” Increase the number of input These options can be broken down into targets.

  • Page 8: Eu Setup

    4) Momentarily press down on the selection EU Setup dial to set the digit. 5) Repeat steps 2-4 to set up remaining digits. Pulses per unit time:  6) When done select “ ” to move to next step. 000001→ (Figure 18).

  • Page 9: K-Factor Setup

    K-factor Setup 12) After choosing to enable or disable the digital output you will be prompted to enable or disable the analog output. Gpm BPH LPM LPH GPH m^3/h DAC Output Enable* m^3/min cfm ft^3/h Disable Figure 22: Unit Selection. Figure 26: Analog Output 1) Select needed unit of measure to be Analog Setup...

  • Page 10: Analog Setup

    Analog Setup 4) Momentarily press down on the selection dial. 5) Rotate the selection dial until the digit FTC* changes to the desired digit. Disable Back 6) Momentarily press down on the selection Figure 27: Analog Menu. dial again to set the value. 7) Repeat steps 3-6 to set up the remaining “FTV”...

  • Page 11: Updating Firmware

    Updating Firmware USER CONFIGURATION WILL BE RESET (INCLUDING PASSWORD) AND THE DEVICE WILL NEED TO BE RECONFIGURED UPON COMPLETION OF A FIRMWARE UPDATE. DO NOT POWER DOWN DEVICE DURING FIRMWARE UPDATE. If needed contact factory for latest firmware. It may be available on our website for download.

  • Page 12: Usb Setup Mode

    USB User Interface defaults. Overview Configuration of the 4057 can be done through the USB port by using the 4057 Series Configuration Software. Using this simple user interface allows quick set up times and batch programming of devices that have the same Figure 3B: Help parameters.

  • Page 13: Mode Setup

    Mode Setup Unit Selection Setup Figure 4B: Mode Selection Figure 6B: EU “Scalar" Enables set up of multiplier, Here you can select Hz or an EU divider, DAC, and engineering units. (Engineering Unit). If an EU is selected you will need to fill in the target count. This is “K-factor”...

  • Page 14: Digital Output Setup

    Digital Output Setup Invert Output Setup Figure 10B: Invert Output Checking this box will invert the digital output when compared to the input. Figure 8B: Digital Output The invert option is only available for a “Multiply” Select this option to increase scalar setup with the divider function enabled.

  • Page 15: Display Settings Setup

    FOR THE 4057 TO RECOGNIZE THE FILE: in_cfg.csv A FILE WILL BE GENERATED ON THE USB (output_cfg.csv). THIS FILE CAN BE USED TO CONFIRM CONFIGURTAION OF THE DEVICE OR CAN BE SENT TO SPECTEC FOR EVALUTAION IF AN ISSUE OCCURS.

Table of Contents