Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Holzstar SAA 901
Summary of Contents for Holzstar SAA 901
- Page 1 Operating Instructions Chip Extraction Unit SAA 901 SAA 901...
-
Page 2: Table Of Contents
13.2 Spare parts drawing ........16 as use and notification of its content is not permitted 14 EU Declaration of Conformity ......17 without explicit consent. Infringements will lead to claims for damages. Subject to technical changes and errors. SAA 901 | Version 1.01... -
Page 3: Introduction
This combination of symbol and signal term indica- tes a potentially hazardous situation which may cause minor or light injuries if it is not averted. SAA 901 | Version 1.01... -
Page 4: Operator Responsibility
- During the entire machine operating time opera- tors must check whether the operating instructions they created meet current standards and adapt the operating instructions where necessary. SAA 901 | Version 1.01... -
Page 5: Personal Protective Equipment
The face protection prevent the face of objects flying By concentrated and farsighted work and action you around. can diminish the rest risk. SAA 901 | Version 1.01... -
Page 6: Safety Aspects In Dealing With Electricity
1. Use only dust bags which are not damaged. the Extraction Unit if you are not concentrated. 2. Use only original Original-Holzstar-dust bags. 12.The operation or servicing of the Chip Extraction Unit is forbidden for people who are less than 18 years or 3. -
Page 7: Safety To Operation
11. To avoid contact with the blower wheel, unused exhaust connections must always be covered. 12. While working outside good footwear is recommen- ded. 13. Keep the working area free of rubbish. 14. All protective devices must be mounted immediately after servicing. SAA 901 | Version 1.01... -
Page 8: Designated Use
Every different use except of the designated use is con- sidered as a false use. Fig. 2: Type plate SAA 901 The exhaust system has not been designed for commer- Transport, packaging, storage cial, craft or industrial use. -
Page 9: Machine Description
- The machine state and machine table must be stable, level and free of vibrations ground. Fig. 3: Chip Extraction Unit SAA 901 - The installation or worker area must be dry and well ventilated. 1 Dust bag hook 2 Dust bag - The ambient temperature must be within -10 °to +... -
Page 10: Set Up The Chip Extraction Unit
Schritt 5: Inspect regularly the chip bag and empty it if is full. Schritt 6: Before operating the on / off switch, make sure that the filter bag is good fixed. SAA 901 | Version 1.01... -
Page 11: Installation Of The Chip Extraction Unit
Step 2: Slide the side plates (12) over the screws on the plastic housing (13) and fasten them with the nuts (E) as shown in Fig.5. Fig. 8: Mounting dust bag Fig. 5: Mounting side plates SAA 901 | Version 1.01... - Page 12 Step 9: Insert a hose attachment (A) over the suction hose (11) as far as it will go against the suction connection of the appliance and secure it with the hose clamp (A) as shown in Fig. 12. SAA 901 | Version 1.01...
-
Page 13: Operation
The exhaust system has a standard chassis. To trans- port the exhaust system, lift slightly on the transport han- dle (4) (Fig.14) and drive to the desired location. Fig. 14: Chassis SAA 901 | Version 1.01... -
Page 14: Malfunctions, Potential Causes And Remedies
Disused machines must be decommissioned immedi- ately to prevent unintended use at a later point and put- ting the environment or persons at risk. - Disposable environmental in hazardous operating materials from the end of life device. SAA 901 | Version 1.01... -
Page 15: Disposal Of Electrical Equipment
33 in the spare parts drawing. points out that this product is not to be treated as a normal domestic waste, but must be deli- - Device type: Chip Extraction Unit SAA 901 vered to collecting company for the recycling - Article number: 5923901 of electric and electronic devices. -
Page 16: Spare Parts Drawing
The following drawing are intended to help identify the necessary spare parts. To order, please send a copy of the part drawing with the marked components to your dealer. Fig. 15: Spare parts drawing SAA 901 SAA 901 | Version 1.01... -
Page 17: Eu Declaration Of Conformity
Part 1: General requirements DIN EN 62233:2008 Measurement methods for electromagnetic fields of household appliances and similar apparatus with regard to human exposure Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Responsible for documentation: Hallstadt, 13.04.2016 ______________________ Kilian Stürmer Manager SAA 901 | Version 1.01... - Page 18 www.holzstar.de...
Need help?
Do you have a question about the SAA 901 and is the answer not in the manual?
Questions and answers