Summary of Contents for Steris Basil 3600
- Page 1 UNCRATING/INSTALLATION INSTRUCTIONS ® Basil 3600 Bedding Dispenser (2009-03-31) P122997-217...
-
Page 2: A Word From Steris Corporation
Once installed, equipment operation should be tested by a qualified service technician prior to use. If STERIS supervision is desired for installing and starting up this equipment, contact STERIS for pricing and availability of this service in your region. -
Page 3: Service Information
Please contact STERIS for details. STERIS carries a complete line of accessories for use in this equip- ment. A STERIS representative will gladly review these with you. Manufactured by:... -
Page 4: Table Of Contents
TABLE OF CONTENTS Section Number Description Page A WORD FROM STERIS CORPORATION ..............I Advisory ................................i Indications For Use ............................i Service Information ............................ii 1 SAFETY PRECAUTIONS ..................1-1 2 UNCRATING INSTRUCTIONS ................2-1 2.1 Open Crates ............................2-1 2.2 Move Sections and Remove Skids ......................2-2 2.3 Prepare Bedding Dispenser For Installation .................. - Page 5 LIST OF ILLUSTRATIONS Figure Description Page Section 2: Uncrating Instructions Crates .............................. 2-2 Section 3: Installation Instructions Disconnect Switch For Electrical Supply ..................3-1 Installing Conveyor .......................... 3-3 Dust Collection System ........................3-4 Conveyor Motor Wiring ........................3-5 Section 5: Operational Test Adjust Cage Size For Flip-Over Rotation ..................
-
Page 6: Safety Precautions
Fans and motors have rotating parts and pinch points. When operating a unit equipped with dust collec- tion system, ensure exhaust guard, elbow and dust bag are securely in place. Repairs and adjustments to this equipment must be made only by STERIS or STERIS-trained service personnel. Non-routine maintenance performed by unqualified personnel or installation of unauthorized parts could cause personal injury, result in improper equipment performance, void the warranty or result in costly damage. - Page 7 CAUTION – POSSIBLE EQUIPMENT DAMAGE: After utilities are connected to equipment, slowly remove the protective adhesive paper from the exte- rior cabinet panels to reduce the level of static discharge. Ensure a cooling fan is attached to rear motor shaft. Verify fan blades are positioned to send airflow to motor.
- Page 8 The table below contains symbols which may be on the crate of your Basil 3600 Bedding Dispenser: Table 1-1. Definition of Symbols Symbol Definition Maximum Shipping and Storing Temperature. Maximum Humidity Level. This Way Up. Do Not Stack. Fragile. Keep Dry.
- Page 9 The table below contains symbols which may be on the identification nameplate of your Basil 3600 Bedding Dispenser: Table 1-3. Definition of Symbols Symbol Definition MOD. Model Number of Bedding Dispenser. SER. Serial Number of Bedding Dispenser. Power Rating of Bedding Dispenser.
-
Page 10: Uncrating Instructions
UNCRATING INSTRUCTIONS IMPORTANT: A listing of the Safety Precautions to be observed when uncrating/installing and testing this bedding dispenser can be found in S 1 of this manual. Do not begin uncrating/installing the ECTION equipment until you have become familiar with this information. 2.1 Open Crates NOTE: Before opening any crates, note the following: 1) Unit weighs approximately 1,800 lb (816 kg). -
Page 11: Move Sections And Remove Skids
Figure 2-1. Crates 2.2 Move Sections and 1. With units still mounted on skids, use a forklift to move both sec- tions to installation site. Remove Skids 2. Remove six lag bolts securing each section base to skid. 3. Remove and discard skid from under each section. If necessary, use a piece of plywood as a small ramp to slide each section WARNING –... -
Page 12: Prepare Bedding Dispenser For Installation
2.3 Prepare Bedding NOTE: Do not remove protective adhesive paper from the exterior cabinet panels until after utilities are connected. Dispenser For Installation 1. Remove all tape from bedding dispenser. 2. Locate electrical box compartment keys located in an envelope taped on bedding dispenser electrical box. -
Page 13: Installation Instructions
Con- b. Utility service lines: tact STERIS regarding service • Disconnect switch (not provided by STERIS) must be options. installed in electric supply line near bedding dispenser (see Figure 3-1). Disconnect switch must be capable of being locked in OFF position only. -
Page 14: Technical Specifications
Verify equipment drawing or identification nameplate, located in chemical storage compartment, for proper voltage and amperage. 3.2.1 Voltage, Amperage and The Basil 3600 Bedding Dispenser operates on: Power Consumption • 208 V, 60 Hz, three-phase, neutral, four-wire •... -
Page 15: Installing Conveyor
AND/OR EQUIPMENT DAMAGE 20 x 3/4" bolts. HAZARD: Repairs and adjust- ments to this equipment must 3. Install dust deflectors. be made only by STERIS or STERIS-trained service person- nel. Non-routine maintenance performed by unqualified per- SIDE VIEW sonnel or installation of unau-... -
Page 16: Installing Dust Collection System
3. Ensure black hose does not hang or form humps below suction ments to this equipment must be system inlet level to avoid a loss of suction or hose being made only by STERIS or STERIS- clogged. trained service personnel. Non- routine maintenance performed 4. -
Page 17: Connect Utilities
Red wire with T1 ments to this equipment must be • Black wire with T2 made only STERIS STERIS-trained service person- • Blue wire with T3 nel. Non-routine maintenance 3. If bedding dispenser is to be used with a Basil 6700 Tunnel ®... -
Page 18: Cleanup
3.6 Cleanup 1. Remove any adhesive found on panels with a small amount of nonflammable cleaning solvent. Keep solvents away from all painted surfaces or damage may result. WARNING – HEALTH HAZARD: 2. Remove all protective paper from unit cabinet panels. Slowly Vapors from solvents can be peel paper away from stainless steel to reduce level of static dis- harmful. -
Page 19: Installation Checklist
Dispenser is installed and prior to performing operational test to help ensure complete and correct installation. NOTE: Contact STERIS to schedule a technician to test your installa- tion and demonstrate proper equipment operation. ❑ Disconnect switch (not provided by STERIS), capable of being... -
Page 20: Operational Test
OPERATIONAL TEST IMPORTANT: A listing of the Safety Precautions to be observed when uncrating/installing and testing this bedding dispenser can be found in S 1 of this manual. Do not begin uncrating/installing the ECTION equipment until you have become familiar with this information. Start-Up Test See Figure 5-1. - Page 21 Units Up to S/N 3609009000 Adjustment Positions (x 3) Adjustment Rod Units From S/N 3609109000 IMPORTANT: Shear bolts are a safety device in case something gets clogged in rotating roller. Please replace with proper bolt to ensure safety device functionality. Nylon Shear Bolt Adjustment...
-
Page 22: Transfer Plates For Different Bedding Types
5.2 Transfer Plates For See Figure 5-2. Different Bedding To help ensure Basil 3600 Bedding Dispenser performance at ® Types peak capability, customer can choose to install either of the follow- ing transfer plates depending on the bedding used: the curved transfer plate with bedding fall guide or the flat transfer plate (see WARNING –... -
Page 23: Curved Transfer Plate With Bedding Fall Guide
5.2.1 Curved Transfer Plate See Figure 5-3. With Bedding Fall Guide IMPORTANT: Lock all electrical supply to bedding dispenser before changing transfer plates. WARNING – ELECTRIC SHOCK Install curved transfer plate and bedding fall guide as follows: AND/OR BURN HAZARD: 1. - Page 24 Detail B Detail A Detail D Detail C Figure 5-3. Installing Curved Transfer Plate and Bedding Fall Guide Operational Test Uncrating/Installation Instructions 122997-217...
-
Page 25: Flat Transfer Plate
Detail A Detail B Figure 5-4. Installing Flat Transfer Plate BASIL 3600 BEDDING DISPENSER IS NOW READY FOR NORMAL OPERATION. Contact STERIS for a demonstration on how to operate the equipment. Refer to Operator Manual (P122996-163) for bedding dispenser operating instructions.
Need help?
Do you have a question about the Basil 3600 and is the answer not in the manual?
Questions and answers