Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for FarmChem APX DPM10G
Summary of Contents for FarmChem APX DPM10G
- Page 1 Digital Preset Meter Manual DPM10G 800.247.1854 | www.FarmChem.com...
-
Page 2: General Safety Regulations
Do NOT stop or deflect leaks with hands, body, gloves or rags • Do NOT dispense valves toward any person or any part of the body • Do NOT place hands or fingers over the end of or into the dispense valve FarmChem | www.FarmChem.com... -
Page 3: Intended Use
Comply with all local, state, and federal fire, electrical and safety regulations • Use of the product in a manner other than specified in this manual may result in bodily injury or impaired operation or damage to the meter 800.247.1854 | FarmChem... -
Page 4: Operation
B. Apply meter to hose Close the drain valve before starting this procedure. Attach swivel to meter. Apply thread sealant to the male end of the hose. FarmChem | www.FarmChem.com... -
Page 5: Operating The Meter
(1) and the manual valve (2) of the spout. First, the pump must be switched off. Then, unscrew the tip of the valve (2) During this discharging operation, do not use the trigger (3). 800.247.1854 | FarmChem... - Page 6 Pull the trigger to dispense. Manual Mode Pull the trigger to begin the flow. When the desired amount has been pumped, press OK/STOP to stop the flow. Release the trigger to stop dispensing. Press RESET to reset counter display FarmChem | www.FarmChem.com...
- Page 7 OK/STOP until the meter displays: WARNING In all cases the operator must attend to the meter while dis- AUTO message pensing in AUTO mode in order not blinking to avoid any oil spillage. Reset batch total 800.247.1854 | FarmChem...
- Page 8 Press and hold on OK/STOP to set the before the preset value is reached, just function: it contains value setting (C-2), press OK/STOP to stop. unit setting (C-3), decimal digits setting (C-4), reset setting (C-5), auto reset set- ting (C-6), and calibrating setting (C-7). FarmChem | www.FarmChem.com...
- Page 9 30 • If the TOTAL indicates a value oth- seconds until the screen disappears. er than zero, this value is automat- The setting will be written in flash then. ically converted from one unit to another unit 800.247.1854 | FarmChem...
- Page 10 To allow the operator to obtain the highest stop precision, the unit is equipped with a Stop Precision factor, or PS factor. The operator can customize the meter to select a PS factor between ZERO and FOUR. FarmChem | www.FarmChem.com...
- Page 11 Instead, to complete the final stages of the filling operation into the calibrated contain- er, top-off in small increments. This is Blinking achieved by rapidly pulling the trigger of the meter and then releasing it very quickly. 800.247.1854 | FarmChem...
- Page 12 Press AUTO again to modify the value After correction: to equal the volume of the calibrated container. Press AUTO again, the meter will calcu- late the K Factor automatically which Press key “10” to increase the indicat- is blinking. ed value. The meter stores the new Calibration Factor (K Factor) and displays: Press key “0.1”...
- Page 13 D. Battery replacement 9V DC battery is applied for power supply when voltage is below 6.5V, screen of flowmeter will flash and the meter cannot be used any longer, which means battery must be replaced immediately. Battery replacement must be processed under dor- mancy mode after screen disappears for the sake of reliable setting preservation.
- Page 14 EXPLODED AND PARTS LIST...
-
Page 15: Troubleshooting
Code Name Quantity Code Name Quantity Right cover Cross recessed pan tap- Meter cover ping screw Front label Washer flat Main circuit board Left cover Cross recessed pan tap- Flexible spout ping screw Filter Screw Seat Meter holder Washer Body Spring Shaft Swivel...