Advertisement
Quick Links
"Global Pool Products is committed to engineering and manufacturing world class products in the pool industry"
RIP TIDE ASSEMBLY & INSTALLATION
GUIDE
www.global-poolproducts.com
Global Pool Products
1330 Pigeon Rd
Bad Axe, MI 48413
Information contained in this document is proprietary and confidential to
P: 989-269-5900 - TF: 866-712-0606
Global Pool Products and not to be reproduced without
Fax: 989-269-5902
written consent from Global Pool Products.
www.global-poolproducts.com
Page | 1
Advertisement
Related Manuals for Global Pool Products GPPSRT-GRAY-R
Summary of Contents for Global Pool Products GPPSRT-GRAY-R
- Page 1 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” RIP TIDE ASSEMBLY & INSTALLATION GUIDE www.global-poolproducts.com Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to...
-
Page 2: Table Of Contents
“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” RIP TIDE SLIDE TABLE OF CONTENTS Introduction PAGE 3 Rip Tide Post Installation Instructions PAGE 4 Maintenance Instructions PAGE 4 Rip Tide Slide Placement/Stub Up... -
Page 3: Introduction
Examine all parts thoroughly prior to installation to avoid anything that may have been damaged in transit. A damaged part should not be used in the installation of this slide. Contact Global Pool Products if any parts arrived damaged. Proper assembly and installation of the Rip Tide Slide is imperative. Not following the directions provided will void Global Pool Products Warranty and may affect the safety of the slide rider. -
Page 4: Maintenance Instructions
“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” POST INSTALLATION CHECKLIST FOR RIP TIDE SLIDE Installer to review with slide owner upon completion of slide installation. Examine: The flume for any apparent cracks or gashes. -
Page 5: Rip Tide Slide Placement/Stub Up
“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Placement/Stub-up Location – Right Hand (Pivot 1) Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to... - Page 6 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Placement/Stub-up Location – Left Hand (Pivot 1) Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to...
- Page 7 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Placement/Stub-up Location – Left Hand (Pivot 2) Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to...
- Page 8 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Placement/Stub-up Location – Right Hand (Pivot 2) Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to...
- Page 9 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Specifications Product Numbers and Shipping Weights: Model Number Description Shipping Weights Rip Tide – Gray Granite Right GPPSRT-GRAY-R 195 lbs (102 kg) Rip Tide –...
- Page 10 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Specifications Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to...
- Page 11 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Slide Water Safety Envelope Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to...
- Page 12 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” RIP TIDE ASSEMBLY INSTRUCTIONS Tools Needed: 1. 3/16” Allen Wrench 9. 5/8” Deep Well Socket PTFE (Teflon) Tape 10. 9/16” Deep Well Socket 2. 7/32” Allen Wrench PTFE (Teflon) Glue 3.
- Page 13 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Prior to the Start of Assembly: o Utilize the cardboard that the slide shipped in as a barrier between your slide components and the surface that the slide is being assembled on to prevent any scuffs and scratches.
-
Page 14: Rip Tide Assembly
“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Rip Tide Assembly Instructions STEP 1 Attaching the base to the lower flume a. Use bag one from the hardware kit to attach the lower flume to the base b. - Page 15 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 2 Installing the foam gasket and butyl on the lower flume a. Measure the center of lower flume, use the two through bolt holes as measuring points, put a mark with a sharpie low enough so it is not visible once the slide is assembled b.
- Page 16 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 3 Attaching the middle flume to the lower flume a. Use two people to lift the middle flume and place it onto the lower flume, they lock into place with the grooved design b.
- Page 17 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 4 Installing a foam gasket and butyl to form the dual gasket on the middle flume a. Measure the center of the middle flume, use the two through bolt holes as measuring points, put a mark with a sharpie low enough so it is not visible once the slide is assembled b.
- Page 18 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 5 Attaching the upper flume to the middle flume a. Use two people to lift the upper flume and place it onto the middle flume, they lock into place with the grooved design b.
- Page 19 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 6 Attaching the plumbing a. Use the PVC fitting in bag six from the hardware kit to hookup the plumbing in the upper ladder b.
- Page 20 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 7 Attaching the upper ladder to the lower ladder a. Stand the lower ladder upright, place the upper ladder on top and guide the remaining flex hose into the lower ladder b.
- Page 21 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 7.5 Installing the dual seal on the upper ladder a. Measure the center of the ladder, use the two through bolt holes as measuring points, mark center with a sharpie b.
- Page 22 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 8 Attaching the ladder to the flume assemblies a. From bag eight in the hardware kit, use two 3” studs and install them into the upper flume, tighten them using a 3/16”...
- Page 23 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 9 Installing the inner connections between the ladder and the flume a. From bag nine in the hardware kit, use two 3/4” hex bolts, each with one flat washer, insert them into the two lower connection points inside the ladder b.
- Page 24 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” STEP 10 Installing the access cover plate a. From bag ten in the hardware kit, use six Phillips head screws to secure the access panel on the upper ladder b.
- Page 25 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Optional Lighting Preparation 1. Install 1” conduit next to the water stub-up before concrete is poured. 2. Run the conduit outside of the concrete pool deck either to the pool equipment or a junction box.
-
Page 26: On Deck Mounting & Plumbing Instructions
“Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” ON-DECK MOUNTING & PLUMBING INSTRUCTIONS Required Tools: ½” SDS Concrete Bit Hammer Hammer Drill Shop-vac 4 ¾” Hole Saw (for garden hose hook-up option) - Page 27 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” 6. Clear all anchor holes from any debris. Shop-vac may be required if debris gets in anchor holes. 7. Plumb the slide to stub up location.
- Page 28 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Pool Slide Installation – Paver Pool Deck Tools Required ½” Concrete Drill Bit ¾” Socket or Wrench Chalk Line Hammer Hammer Drill Hardware Rip Tide, Tidal Wave, Tsunami (10) –...
- Page 29 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to P: 989-269-5900 - TF: 866-712-0606...
- Page 30 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to P: 989-269-5900 - TF: 866-712-0606...
- Page 31 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” Global Pool Products 1330 Pigeon Rd Bad Axe, MI 48413 Information contained in this document is proprietary and confidential to P: 989-269-5900 - TF: 866-712-0606...
- Page 32 “Global Pool Products is committed to engineering and manufacturing world class products in the pool industry” * Hardware attaches through access plate on back side of ladder section *GPP-B375x75HHCS 3/8” x ¾” Hex Bolt QTY. 4 *GPPBW375 WASHER QTY. 4...
Need help?
Do you have a question about the GPPSRT-GRAY-R and is the answer not in the manual?
Questions and answers