Related Manuals for Tek-Trol Tek-Flux 1400C
Summary of Contents for Tek-Trol Tek-Flux 1400C
- Page 1 Quick Start Guide Tek-Flux 1400C Utility Electromagnetic Flow Meter Battery Powered 796 Tek Drive, Crystal Lake, IL 60014 USA +1 847 857 6076 +1 847 655 6147 www.tek-trol.com...
-
Page 2: Before You Begin
Before connecting a HART-based communicator in an explosive atmosphere, make sure that the instruments of the loop are installed by intrinsically safe or non-incentive field wiring practices. Make sure only qualified personnel perform the installation. 2. Unpack Tek-Flux 1400C Utility Electromagnetic Flow Meter 3. Dimensional Drawings • Battery Powered TRANSMITTER... - Page 3 14 3/4" (368) 19 1/2" (485) 19 1/2" (485) 17 1/4" (432) Ø25 X 12 • Line Powered Flow Tube with Metal body 165mm Transmitter Housing Ansi 150 105mm Flange Earthing Cable Earthing Ring Fig 2: Integral Type Tek-Flux 1400C...
- Page 4 44 1/2” (1115) 24 1/2” (615) 40” (1000) 24 1/4” (615) 29” (724) 48 1/2” (1214) 40” (1000) 49 1/4” (1230) 26 1/4” (655) 796 Tek Drive, Crystal Lake, IL 60014 USA +1 847 857 6076 +1 847 655 6147 www.tek-trol.com...
- Page 5 The Transmitter is delivered in a powered-up condition, and hence you will not normally see this screen, except when connecting a replacement battery. Ĕ Run Time The Transmitter is delivered in a powered-up condition, and hence you will not normally see this screen, except when connecting a replacement battery. Tek-Flux 1400C...
- Page 6 9999999.9g Enabled: only Flow Rate, Velocity Enabled: only Total 99999.999g pm 9.999 /s 9999999.9g Enabled: only Flow Enabled: only Velocity 99999.999 9.999 /s 796 Tek Drive, Crystal Lake, IL 60014 USA +1 847 857 6076 +1 847 655 6147 www.tek-trol.com...
- Page 7 +9.999 /s 9999999.9g Enabled: only Flow Rate +99999.999 gpm +9.999 /s -9999999.9g Enabled: only Total +9.999 /s +9.999 /s +9999999.9g 9999999.9g +9.999 /s Enabled: only Flow Rate, Velocity +9999999.9g +99999.999 gpm +9.999 /s Enabled: only Velocity +9.999 /s Tek-Flux 1400C...
-
Page 8: Power Supply
Green RS485- Modbus Note: Use a JB with appropriate IP rating Fix the JB cover and fasten its screws Fig 5: Junction Box 796 Tek Drive, Crystal Lake, IL 60014 USA +1 847 857 6076 +1 847 655 6147 www.tek-trol.com... -
Page 9: Installations
Never install the flow tube in an empty or partially full pipeline. Never install the flow tube in vertical pipelines, where the liquid flow direction is downward. Flow direction Fig 8: Vertical Installation with Liquid in the Downward Direction Tek-Flux 1400C... - Page 10 Main menu Sub menu Sub menu Edit menu level - 1 level - 2 level - 3 796 Tek Drive, Crystal Lake, IL 60014 USA +1 847 857 6076 +1 847 655 6147 www.tek-trol.com...
-
Page 11: Troubleshooting
Set correct communication incorrectly set. parameters Correct Pulse settings in respective Pulse settings are not correct. DO section. Pulse is not available. b. Pulse type is not known. b. Check your ordering for Active or Open Collector Output. Tek-Flux 1400C... - Page 12 796 Tek Drive Crystal Lake, IL 60014, USA Sales: +1 847-857-6076 Tek-DPro Flow Solutions Tek-Trol Solutions BV Tek-Trol Middle East FZE PO Box 121 Windsor, Colorado Florijnstraat 18, 4879 AH SAIF Zone, Y1-067, PO BOX No. 80550, USA Etten-Leur, Netherlands...
Need help?
Do you have a question about the Tek-Flux 1400C and is the answer not in the manual?
Questions and answers