Advertisement
Quick Links
1.
WARN
NING
This
device comp
plies with par
cond
ditions: (1) Th
his device ma
any
interference
received, inc
2.
Produ
uct feat
The C22J
module is d
m
capa
abilities.The s
system's bloc
It em
mbedsFlash, L
LDO and DCD
leve
l of the modu
ule, few exter
requ
uirements.
Its ty
ypical applica
ations include
Smartphone
e and tablet a
RF Remote C
Control
Sports and f
itness trackin
Wireless toy
ys
Smart Lighti
ng, Smart Ho
C22J
rt 15 of the FC
CC Rules. Ope
ay not cause h
harmful inter
cluding interf
ference that m
tures
designed to
offer high
k diagram is a
as follow.
DC, crystal, RF
F match netw
rnal compone
ents are need
e, but are not
limited to th
accessories
ng
ome devices
eration is sub
bject to the fo
ference, and
(2) this devic
may cause un
ndesired o per
integration,
ultra‐low p
work and etc. W
With the high
ded to satisfy
y customers' u
e following:
ollowing t wo
ce must accep
pt
ration.
power applica
ation
h integration
ultra‐low cost
t
Advertisement
Summary of Contents for niu C22J
- Page 1 Produ uct feat tures The C22J module is d designed to offer high integration, ultra‐low p power applica ation capa abilities.The s system’s bloc k diagram is a as follow. It em mbedsFlash, L LDO and DCD DC, crystal, RF...
- Page 2 C22J Key fe eatures s eneral featu res Up to 7 GPI Os Communi ation, 2xUARTs , D Download an d clock r rate can be from 3.2 kHz to 6.5 M Hz 24 bits audi io quality ℃~+85℃ Operating t temperature range: ‐20℃ Supports Bl uetooth 5.0 classic and l ow energy lash features s C22J J module em...
- Page 3 C22J Pin la yout TOP view Pin fu nction ns No PinName Type Descr ription 1 GPIO1 Digital I/O O Genera al input/outpu 2 GND GND GND 3 ANT Analog RFsing al 4 GND GND GND 5 ...
- Page 4 C22J 6. Size 13.4(m mm)*11.4(mm m)*2.8(mm) Absolu ute ma aximum m ratin ngs Auxilia ary equ uipme nt PCBA Antenn na: PCBA_BT T_ATA_1.0(t type) Anten na per rforma ances the follo wing Please ensu ure the pea ak gain of...
- Page 5 C22J module must be only approved for use when installed in devices produced by a specific manufacturer. If any hardware modify or RF control software modify will be made by host manufacturer,C2PC or new certificate should be apply to get approval, if those change a nd modification made by host manufacturer not expressly approved by the party responsible for compliance, then it is illegal. FCC Radiation Exposure Statement The module can be installed or integrated in mobile or fix devices only. This module cannot b e installed in any portable device. This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co‐located or operating i n conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the f ollowing: “Contains Transmitter Module FCC ID: 2AZ6G‐C22J Or Contains FCC ID: 2AZ6G‐C22J” OEM INTEGRATION INSTRUCTIONS: This device is intended only for OEM integrator under the following c onditions: The module must be installed in the host equipment, and the transmitter module may not be co‐located with any other transmitter or antenna. The module shall be only used with the internal on‐board antenna that has been originally tested and certified with this module. External antennas are not supported. As long as these 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end‐product for any additional ...
- Page 6 C22J 1. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part15 of the FCC Rules. These limits are designed to provide r easonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for h elp. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the product. Any company of the host device which install this modular with limit modular approval should perform the test of radiated & conducted emission and s purious emission, etc. according to FCC CFR Part 15C: 15.247 and 15.209&15.209, 15B class B requirement, Only if the test result comply with FCC CFR Part 15C: 15.247 and 15.209&15.209, 15Bclass B requirement then the host can be sold legally. ...