Summary of Contents for LARS LAJ TRESS 13072
- Page 1 13072 NATURE Product name: Firehouse Catalogue number: 13072 Dimensions: 535x465 cm Total height: 309 cm 535 cm Top and side view with safety zone in scale 1:100...
- Page 2 13072 Product logbook PRODUCT DATA COMPANY DATA Product name: Firehouse Name: Catalogue No.: 13072 Address: Product type: NATUR Zip code/city: Place: Critical Falling Height: Phone: Dimensions: 535x465 Fax: Safety Zone: Email: Age Level: years Product Photo/Picture OWNERS DATA Name: Contact: Address: Zip code/city: Place:...
- Page 3 13072 Product main dimensions NATURE [cm]...
- Page 4 INSTALLATION MANUAL 13072 Page 1 of 7 Step 1: Dig foundation ditches for each post (see drawing below). Install the posts in their positions ensuring their stability. Post 1900 Step 2: Install the horizontal beams on the posts using wood connectors and screws. Pour the foundation concrete for each post and leave to dry.
- Page 5 INSTALLATION MANUAL 13072 Page 2 of 7 Step 3: Measure and drill holes in 6 beams L: 2200 corresponding with the holes in the grating plates of the steel grill and making sure the measurements shown below apply. Steel gril Gril beam L=2200 Step 4: Pre-assemble the roof on the ground (beams with steel grill): connect the beams with the grating plates using M10 bolts.
- Page 6 INSTALLATION MANUAL 13072 Page 3 of 7 Step 5: Place the pre-assembled roof construction on the vertical posts and connect using L- shaped steel connectors following the drawing below. Roundhead screw 6x40 Six angle head screw 8x80 Washer 8x24 Washer 10x20 Bolt M10x120 Self locking nut M10...
- Page 7 INSTALLATION MANUAL 13072 Page 4 of 7 Step 7: Install two threaded rods fi 12 using the L shaped connectors. The rods should cross at the centre of the firehouse . Once assembled, install the hook on the junction. Threaded road O12 Roundhead screw 6x40 Self locking nut M10...
- Page 8 INSTALLATION MANUAL 13072 Page 5 of 7 Step 8: Cover the roof with boards. Start with the longest board (2600) fixing it to the edge using 4x35 wood screws. Step 9: Proceed with the other boards (2500), starting from the board already assembled and going up to the top of the roof.
- Page 9 INSTALLATION MANUAL 13072 Page 6 of 7 Step 10: Assemble the palisade shingles L: 2500 using wood screws 5x100 spacing them about 350 for each other. Cut the shingle to fit the size of the roof. Wood screw 5x100 Torx [mm]...
- Page 10 INSTALLATION MANUAL 13072 Page 7 of 7 Step 11: Place the benches under the roof, between the posts. Nature bench [mm]...
- Page 11 16.12.2014...
- Page 12 FA 4x35 S4x25 S4x35 F6x50 S5x50 F6x70 S5x70 S6x70 F8x70 S5x100 F8x80 F8x90 F10x120 F8x120 S3,5x16 S4x30 S6x40 S6x50 M10x40 S6x70 B6x50 S4,2x13 M10x60 S4x25 M8x70 B8x65 M8x120 B8x75 SI 6x25 SI 6x30 R3,2x12 R5x18 6x18 8x24 10x20 15x28 Pre drill before screw. Hole in wood for screw: one size smaller than screw.