Advertisement
Quick Links
Advertisement
Summary of Contents for AAMP Global ECHOMASTER PRO ParkAlert PS-TRUCK30
- Page 1 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks User Manual...
- Page 2 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Introduction Congratulations on purchasing EchoMaster PRO parking sensors. This ultrasonic detection system is designed to assist in the avoidance of obstacles while reversing. Disclaimer: EchoMaster® is strictly a driver assistance device, and should not be relied upon as a substitute for safe driving practices.
- Page 3 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Fitting Instructions Recommended Tools Optional Tools for Installation High torque drill, use slow speed Panel tool (for situations requiring plastic, inner (approx 400 rpm) panels to be removed) Grease Pencil and Center Punch Phillips head tip for drill for marking drill point...
- Page 4 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Fitting Instructions - (continued) Sensor Install: Sensors must be installed in order 1-4 from left to right with control module harness entering trunk near sensor #4. Choosing the Correct Angle Sleeve (Optional angle gauge: SP1022) Vehicle is parked on flat and level ground and the parking brake is set.
- Page 5 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Fitting Instructions - (continued) Connecting the Power Harness To find reverse power, remove tail light and examine where and what wires plug into the reverse bulb. Locate and verify with a volt meter. The wire carries 12 volts when in reverse and 0 volts when out of reverse.
- Page 6 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Fitting Instructions - (continued) Choosing Correct Dip Switch Configuration For most vehicles, all switches DOWN will work fine. However, should you need to make changes, please see below. Switch Vertical Angle Down: Original Coverage Range...
- Page 7 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Sensor Assembly Step 1 To take the sleeve off of the sensors lift up on 1 clip and push the sensor out with your thumb. Step 2 Slide the sensor angle sleeves onto the sensors.
- Page 8 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Sensor Painting Step 1 Remove the silicon gasket and disconnect cable before painting the sensors. Certain colors may require a thin coat of primer. Step 2 Paint the front of the sensors and the angle sleeve.
- Page 9 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Wiring Diagram NOTE: If using optional display (PA-DISPLAY) connect to main harness in place of speaker Operating Guide System will become engaged when vehicle is put into reverse. The system should beep one time when reverse is activated to notify the driver that it is on and working.
- Page 10 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Dimensions (mm/in) 63.7mm / 2.5” 2500mm / 98.4” 70.2 / 2.8” 15.0mm/0.9” 21.5mm / 0.8” 24.2mm / 0.95” 26mm / 1.0” 87.3mm /3.4” phone - 1-800-477-2267 email - support@aampglobal.com...
- Page 11 Installation Guide PS-TRUCK30 ParkAlert Digital Rear Sensing System with Extended Harness for Trucks Troubleshooting PROBLEM REASON SOLUTION System is not powered up or Check the power and wrong connection of power ground connections cable System doesn’t react when reverse is engaged Invalid connection between Check the connection speaker/display and control...
- Page 12 15500 Lightwave Drive, Suite 202 Clearwater, Florida 33760 email - support@aampglobal.com phone - 1-800-477-2267 EchoMaster is a Power Brand of AAMP Global. IG-PS-TRUCK30 EchoMaster.com REV 310818...