Advertisement
5. User commands
User commands can be sent from registered telephones without the
MC or UC code, unless the VERIF command is enabled.
5.1. Driver selection by an SMS command
A driver can also be selected with an SMS command (e.g. a function for a
dispatcher). In order to change the current driver's number you have to
enter the following command:
Command format:
UCcode Dx
where:
x – is a driver's number from 1 to 99
Command example:
1111 D2 (to set driver 2)
5.2. Journey type setting
Journey type selection should primarily be carried out with a switch
located in the vehicle interior. If such a switch has not been installed, the
selection can be made with an SMS message.
Command format:
UCcode Tх
where:
х – journey type:
Command example:
1111 T1 (sets a private journey)
5.3. Notification of the commencement of a journey
If the TELINFO telephone number has been set using the MC code,
the function can be enabled or disabled permanently or it can be activated
for a single journey.
Command format:
UCcode SINFO ON/OFF
Command example:
1111 SINFO ON (the unit sends a notification about the commencement
of a journey each time the ignition key is turned on)
Command format:
UCcode SINFO
Command example:
1111 SINFO (the unit sends a one-time notification about the commence-
ment of a journey)
5.4. GEOFENCE function
If the GEOFENCE function parameters have already been set using
the MC code, this function can be activated by the following commands,
either for a single journey or permanently with the possibility of disabling.
When the unit leaves the delimitated area, it sends an SMS to TELINFO.
Command format:
UCcode GEOFENCE ON/OFF
Command example:
1111 GEOFENCE ON (the unit sends a notification each time it leaves the area)
Command format:
UCcode GEOFENCE
Command example:
1111 GEOFENCE (the unit sends a one-time notification when it leaves
the area)
5.5. Auxiliary appliance switching
An auxiliary appliance can be triggered with the AUX command, when the
yellow 12/24V wire is activated. The ON/OFF commands can be used
to change the output state or activate the output for a precisely defined
period of time. The maximum length of this period is 60 minutes
Command format:
UCcode AUX ON/OFF
Command example:
1111 AUX ON (the output will be activated for one hour, unless it is deactivated
with the AUX OFF command)
Command format:
UCcode AUX x y
where
х – number of seconds or minutes
y – s/m seconds or minutes
Command example:
1111 AUX 25 M (activates the output for 25 minutes)
5.6. SMS command reception confirmation
The device can confirm execution of the received SMS commands
to the telephone number from which the command was received. This
function is optional, though.
Command format:
UCcode RE ON/OFF
Command example:
1111 RE OFF (disables confirmation of SMS commands)
5.7. Ascertaining the current position
The current position of the unit can be ascertained by sending a GPS
command. The received SMS contains a link to Google Maps which smart
phones can then use to display the vehicle position on the map.
Command format:
UCcode GPS
Example of a command to ascertain the current position:
1111 GPS
CU-08A Tracer unit
0 is a business trip (default)
1 is a private journey
5.8. Current vehicle status
The current vehicle status can be ascertained with the STATUS
command. The unit reacts to this command with an answer stating the
current status of the unit.
Command format:
Command example:
1111 STATUS
5.9. HELP command
The HELP command can be used to obtain basic help about how to
control the unit using SMS commands.
Command format:
Command example:
1111 HELP
5.10. CREDIT and LOCATOR commands
If the CREDIT and LOCATOR functions have already been set, single
commands can be used to ascertain the credit balance and position.
Command format:
Example of a command for ascertaining the credit balance on a
prepaid card:
1111 CREDIT
Command format:
Example of a command for ascertaining the position in a mobile
operator's network:
1111 LOCATOR
6. Other functions
6.1. Forwarding of unidentified SMS messages
The unit forwards all SMS messages which it is unable to identify
by password or by the caller's number to the TEL1 number. These could
be messages from the operator concerning the credit balance, information
about changes to flat-rate tariff terms and conditions, one-time passwords,
etc.
This function also serves as protection against possible testing
by an unauthorized person trying to break the unit's code.
The forwarded SMS always contains the telephone number from which
the message was sent and the wording of the message with the exception
of the first word which is replaced with asterisks. The maximum number
of forwarded SMS messages is 10 per 24 hours.
6.2. Unit reset
The unit can be reset to default via an SMS command.
Note: In such a case all parameters will be reset to default.
Command format:
Example of a command for unit reset:
1234 RESET MASTER
7. Technical specifications
Power supply voltage
Maximum current consumption
Nominal current in on-line mode
Standby current consumption
working range of the GSM module E-GSM / GPRS
Dimensions without the terminals and mounts
L x W x H
Unit weight
Operating temperature range
Intended for connection to a 12 V or 24 V DC vehicle power supply.
The unit is intended for operation in road vehicles.
This product is identical to the type approved by the Ministry of Transportation
of the Czech Republic under the number E8 10R-04 6950.
E
10R- 04 6950
8
JABLOTRON ALARMS a.s. hereby declares that the CU-08A
is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC, 2011/65/EU and
ECE Regulation No. 10.03.
Note: Although this product does
not contain any harmful materials
we
suggest
the
product
or directly to the producer after
use.
4/4
UCcode STATUS
UCcode HELP
UCcode CREDIT
UCcode LOCATOR
MCcode RESET MASTER
850/900/1800/1900MHz
you
return
to
the
dealer
8 - 30 V
500 mA/12 V
50 mA/12 V
14 mA/12 V
68 x 91x 34 mm
125 g
-20 to +80 °C
MHF27100
Advertisement
