Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch ALLPLEX APC-AEMC-SVR
Summary of Contents for Bosch ALLPLEX APC-AEMC-SVR
- Page 1 ALLPLEX Access Easy Master Controller APC-AEMC-SVR Quick Installation Guide...
-
Page 3: Table Of Contents
General system information Installation of ALLPLEX AEMC Connecting the cables and powering up the panel Default settings of the panel 4.2.1 Retrieving configured IP settings of the panel Robert Bosch (SEA) Pte Ltd Quick Installation Guide F.01U.251.137 | V1.0.0 | 2011.08... -
Page 4: Copyright Notice
All software is provided "AS IS." The sole obligation of BOSCH SECURITY SYSTEMS shall be to make available all published modifications that correct program problems are published within one (1) year from the date of shipment. -
Page 5: Safety And Warranty
11. Restricted Access Locations are required for the installation. 12. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW -20°C (-4°F) OR ABOVE 65°C (149°F). IT MAY DAMAGE THE EQUIPMENT. Robert Bosch (SEA) Pte Ltd Quick Installation Guide F.01U.251.137 | V1.0.0 | 2011.08... -
Page 6: Fcc Information
There is a danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions and your local government’s recycling or disposal directives. F.01U.251.137 | V1.0.0 | 2011.08 Quick Installation Guide Robert Bosch (SEA) Pte Ltd... -
Page 7: System Overview
(-4°F to 176°F) Humidity (Operating) 10% RH to 90% RH Humidity (Storage) 95% @ 40°C, non-condensing Vibration 0.5G / 5 Hz to 500 Hz Shock 15G with 11m/sec Robert Bosch (SEA) Pte Ltd Quick Installation Guide F.01U.251.137 | V1.0.0 | 2011.08... -
Page 8: General System Information
Part Hard Disk Drive LED Power LED Rear panel Figure 3.2 Rear view of the panel Number Key Components Power switch DC-in jack RJ45 10/100/1000BASE-TX Ethernet port F.01U.251.137 | V1.0.0 | 2011.08 Quick Installation Guide Robert Bosch (SEA) Pte Ltd... -
Page 9: Installation Of Allplex Aemc
Set the power switch of the panel on (item 1 of Figure 3.2). Once ALLPLEX AEMC is powered, the PWR LED (item 2 of Figure 3.1) should be lighted up. Robert Bosch (SEA) Pte Ltd Quick Installation Guide F.01U.251.137 | V1.0.0 | 2011.08... -
Page 10: Default Settings Of The Panel
Do not forget any changes made to the default master User ID and/or Password. If you don’t remember them, the information cannot be retrieved on-site. You will need to send the ALLPLEX AEMC to the Bosch Service Center. After logging in, change the IP settings accordingly, and reboot the ALLPLEX AEMC. Once rebooted, ALLPLEX AEMC will respond to its new IP address. - Page 11 MAC address from the scan results to find the corresponding IP address. For more information on other functionalities of IP Setup, please refer to Section 5 Using IP Setup of the Utilities Program Manual. Robert Bosch (SEA) Pte Ltd Quick Installation Guide F.01U.251.137 | V1.0.0 | 2011.08...
- Page 12 Robert Bosch (SEA) Pte Ltd 11 Bishan Street 21 573943 Singapore Singapore www.boschsecurity.com © Robert Bosch (SEA) Pte Ltd, 2011...