Advertisement
Quick Links
Advertisement
Related Manuals for flight of harmony Famine 500
Summary of Contents for flight of harmony Famine 500
- Page 1 Voltage-controlled power starvation Eurorack Module kit...
- Page 2 Contents (1) Front panel (3) PCB (1) Resistor card (1) Semiconductor card (1) Capacitor card (1) Hardware bag (2) 2x8 box header (2) M3x0.5 eurorack mounting screw (2) M3 nylon washer (8) 3/8" locking PCB standoff (2) 1x3 0.1" pitch 0.235" height pin header (2) 1x4 0.1"...
- Page 3 Kit Notes Tools • Soldering iron with large and fine tips • Hot air gun (advised) • Solder • Fine-tip tweezers • Nut drivers/sockets/wrenches: • 7mm (toggle switch) • 8mm (jack nuts) • 10mm (potentiometer nuts) Skills THIS IS NOT A BEGINNER-LEVEL KIT Kit contains both very small (0603) and relatively large (DPAK) components.
- Page 4 Kit Notes (cont.) • Good, fine-tip tweezers are a must. The Wiha 4b and 7a tweezers are great • One helpful trick for soldering SMD with wire solder is to pre-solder one pad for each component location. Next, hold the component in place and touch your soldering iron tip to the pre-soldered pad to reflow the solder.
- Page 5 Kit Notes (cont.) Help If you're still having problems, email me! I am always happy to help. When emailing, please include high-resolution pictures of your circuit boards. Most of the troubleshooting requests I have received were solved by zooming in and closely examining the pictures. Cold solder joints are sneaky and hard to spot if you haven't dealt with them before.
- Page 6 PCB Assembled Front View FAM500-K v1.0 manual Dec. 2022 — p.5/14 www.flightofharmony.com...
- Page 7 PCB Assembled Rear View Oops, should say “Control”. FAM500-K v1.0 manual Dec. 2022 — p.6/14 www.flightofharmony.com...
- Page 8 SMD Reference Also oops. FAM500-K v1.0 manual Dec. 2022 — p.7/14 www.flightofharmony.com...
- Page 9 SMD Reference, cont. FAM500-K v1.0 manual Dec. 2022 — p.8/14 www.flightofharmony.com...
-
Page 10: Exploded View
Exploded View FAM500-K v1.0 manual Dec. 2022 — p.9/14 www.flightofharmony.com... - Page 11 Controls & LED Installation Finger-tight Finger-tight Solder rst These too Set lens to desired height then solder FAM500-K v1.0 manual Dec. 2022 — p.10/14 www.flightofharmony.com...
-
Page 12: Power Cable Assembly
Power Cable Assembly Power in cable (9”/23cm) Power out cable (12”/30.5cm) Socket header (black) Pin header (gray) Triangle indicates pin1 (location of red stripe) FAM500-K v1.0 manual Dec. 2022 — p.11/14 www.flightofharmony.com... - Page 13 Miscellaneous IC Orientation Line/Slope Pin 1 Line/Slope Diode Orientation (OR) LINE LED and capacitor Orientation FAM500-K v1.0 manual Dec. 2022 — p.12/14 www.flightofharmony.com...
- Page 14 Miscellaneous (cont.) Tightening toggle switch jam nuts. Toggle switches are slightly shorter than the jacks and potentiometers, so the jam nut (rear nut) must be run flush with the panel before tightening the outer nut to prevent deforming the panel. Spin ush with panel, do not tighten.
- Page 15 FAM500-K v1.0 manual Dec. 2022 — p.14/14 www.flightofharmony.com...