Aputure LS 1200 Installation Manual

LS 1200 Four-Lights Bracket
Installation Manual
Product Details
7
3
1
9
4
7
8
What's Insided
When you unbox the product, please make sure all the items listed below are included, otherwise, please
contact the seller immediately.
Tips:
1. Before installation, it is recommended that the components be discharged neatly in the following order to improve
installation efficiency.
2. The illustrations in the manual are only diagrams for reference. Due to the continuous development of new versions of the
product, if there are any differences between the product and the user manual diagrams, please refer to the product itself.
Upward
Upward Upward
① ② ③
(1pc) (2pcs) (2pcs)
Detailed product manual can be found on www.aputure.com .
Split lock
washers
M8*45
Screw
5
M6*35
M6*35
Screw
Screw
3. Install the upper of bracket: Place ⑤ as shown,
fix it with 3 sets of M8 * 45 screws & split lock
washers and 8 sets of M6 * 35 screws.
M6*35 M6*35
Screw Screw
6
M8*45
Screw
Split lock
washers
5. Install the lower of bracket: Place ⑥ as shown,
fix it with 3 sets of M8 * 45 screws & split lock
washers and 8 sets of M6 * 35 screws.
5
7
2 4
10
3
2
6
7
8
11
Upward
Upward
④ ⑤ ⑥
(2pcs) (1pc) (1pc)
-1-
Nuts
Nuts
M6*50
M6*50
4
Screw
Screw
4. Install the lower side of bracket: Place ③ and
④ as shown, fix them with 4 sets of M6 * 50
screws & nuts.
M6*10 Screw (4pcs) M6*10 Screw (4pcs)
7
7
M6*10 Screw (4pcs) M6*10 Screw (4pcs)
6. Install the corner guards of middle bracket:
Place ⑦ as shown, fix them with 4 sets of 4
pieces M8 * 45 screws.
-3-
Upward
⑨
(1pc)
(1pc)
Tips for Using Hex Key
1.Quickly tighten screw
Getting Started
Washers
M6*50
Screw
1
Nuts
⑦
(4pcs)
Nuts
⑧
1. Install the middle upper and lower of bracket:
(2pcs)
Place ① and ② as shown, fix them with 4 sets of
M6 * 50 screws & washers and nuts.
Washers
M6*50
Screw
9
Split lock
washers
7. Install the bottom of bracket: Place ⑨ ⑩ ⑪
3
as shown, fix them with 4 sets of M6 * 50 screws
& washers and 2 sets of M8 * 45 screws & split
lock washers.
Washer of
B
7
7
9. Combine the middle and bottom of bracket: Place the components installed in step 6 and step 8 as
shown, pull the bottom bracket handle outward (Figure A), push the bottom bracket from bottom to
top until the handle is flush with the interface on both sides of the component ①, and tighten the left
and right handles to fix them (Figure B)
Split lock
washers
(12pcs)
M6*50 Screw
(24pcs)
M8*45 Screw
（12pcs）
Nuts
Washers
(18pcs)
(6pcs)
Upward
⑪
⑩
(1pc)
2
3
Washers
M6*50
Screw
Nuts
2
2. Install the upper side of bracket: Place ③ and
④ as shown, fix them with 4 sets of M6 * 50
screws and nuts.
-2-
10
11
M8*45
Screw
M6*10 Screw (4pcs)
8. Install the corner guards of bottom of bracket:
Place ⑧ as shown, fix them with 2 sets of 4 pieces
M8 * 45 screws.
handle
1
A
-4-
Washers
M6*35 Screw
of handle
(2pcs)
(24pcs)
Hex key
(1pc)
M6*10 Screw
(36pcs)
Screw Kit
(1pc)
2.Reinforced screw
4
Nuts Nuts
M6*50
M6*50
Screw Screw
8 8
M6*10 Screw (4pcs)
Washer of
handle
B
A