Subscribe to Our Youtube Channel
Related Manuals for LXNAV ADS-B
Summary of Contents for LXNAV ADS-B
- Page 1 ADS-B receiver User manual Version 1.00 LXNAV d.o.o. • Kidričeva 24, 3000 Celje, Slovenia • tel +386 592 33 400 fax +386 599 33 522 info@lxnav.com • www.lxnav.com...
-
Page 2: Table Of Contents
ADSB receiver Version 1.0 June 2022 Important Notices Limited Warranty Packing Lists Technical Data Power and Consumption Size and Weight System description Switching on the Unit Normal operation How the system works Installation Wiring ADSB receiver PORT1 and PORT2 pinout (RJ45) 5.1.1 ADSB receiver RF connector side description 5.1.2... -
Page 3: Important Notices
This RPM flap product is warranted to be free from defects in materials or workmanship for two years from the date of purchase. Within this period, LXNAV will, at its sole option, repair or replace any components that fail in normal use. Such repairs or replacement will be made at no charge to the customer for parts and labour, provided that the customer pays for shipping costs. -
Page 4: Packing Lists
ADSB receiver Version 1.0 June 2022 Packing Lists ADSB receiver 1x FLARMVIEWPF-CA 1x ADSB antena Page 4 of 11... -
Page 5: Technical Data
ADSB receiver Version 1.0 June 2022 Technical Data 2.1 Power and Consumption Table 1: Absolute maximum ratings Parameter Symbol Rating Units Power Supply Power 36.0 Power Consumption Table 2: Electrical characteristics Parameter Symbol Units Power Supply Power 12.0 36.0 2.2 Size and Weight Size: 55mm x 90mm x 25mm Weight: 160g Page 5 of 11... -
Page 6: System Description
ADSB receiver Version 1.0 June 2022 System description 3.1 Switching on the Unit ADSB receiver is switched on automatically, when it gets enough power supply from either PORT In or PORT OUT RJ45 connector. 3.2 Normal operation ADSB receiver goes into normal operating mode, when it receives signals from enough GPS satellites. -
Page 7: Installation
ADSB receiver Version 1.0 June 2022 Installation ADSB receiver has typically connected to the input port a GPS source. This is normally flarm device with NMEA output or classic GPS with standard NMEA output. At the other side is SMA connector for ADSB antenna. Red LED indicates receiving ADSB traffic. -
Page 8: Wiring
ADSB receiver Version 1.0 June 2022 Wiring 5.1 ADSB receiver PORT1 and PORT2 pinout (RJ45) INPUT OUTPUT Pin 8 Pin 1 Pin number Description + Power input + Power input n.c. Ground Data output (TX) Data input (RX) - Power input - Power input Underneath each port there are TX (transmit-green) and RX (receive-red) status LEDs that flash when that port is receiving or transmitting data. -
Page 9: Installation Examples
ADSB receiver Version 1.0 June 2022 5.1.2 Installation examples 5.1.2.1 Flarm - ADSB - FlarmView Flarm or GPS NMEA DATA FlarmView 5.1.2.2 Flarm - ADSB - FlarmLED Flarm or GPS NMEA DATA FlarmLED Page 9 of 11... -
Page 10: Firmware Update
Firmware can be updated via special “flarm update cable”, connected to PC through serial interface. You can get flash loader at: https://gliding.lxnav.com/lxdownloads/firmware/ (S7 PC update tool) For the update you need file named _x*.lxfw (x= version nr.) on your computer. -
Page 11: Revision History
ADSB receiver Version 1.0 June 2022 Revision History May 2017 Rev0 Initial release version 1.00 Page 11 of 11...
Need help?
Do you have a question about the ADS-B and is the answer not in the manual?
Questions and answers