Advertisement
Desono™
DX-S U-Bracket (SPA-UBDXxxx)
Installation Guide
The U-Bracket is a low profile powder-coated marine grade
aluminum design that allows the unit to be connected to a
center suspension post or against the wall, ceiling, or other
flat surface. It can also be mounted to a variety of third party
stand and pole adapters.
A hole drilling template is included in each box to make
installation easier.
Installation
1. Mount the U-Bracket prior to loudspeaker installation.
If mounting it horizontally on a wall, the slots should
face up - see image at right. Route cable through the
channel. Sufficient cable should be pulled through
an unused bracket hole to create a drip loop (damp/
wet applications) with enough extra to connect to the
ClickPlug.
NOTE: If the wall is not finished before the loudspeaker is
mounted, the U-Bracket and cable should be masked with
painter's tape or other masking material.
2. Wire the ClickPlug as shown leaving enough for the
likely mounting angle and a drip loop if necessary. Do
this before mounting the loudspeaker.
2
Thread cable through the gland nut
and barrel into ClickPlug
(2 conductor cable shown)
A:
9300 S.W. Gemini Drive Beaverton, OR 97008 USA
Bolts
1
Structure Mounting Points
(Hardware not provided)
Cable / Wire Size
ClickPlug Cable gland nut will accept a 4-8mm (0.15-.3 in)
diameter cable or 2 pairs 1.5mm2 (16 ga) or 1 pair 2.5mm2
(14 ga). For outside or moisture-rich environments - round
SJOW cable or equivalent is advised to provide a weather-
resistant seal in the tightened gland nut.
Tools Needed
• 5.5mm (or 7/32") Hex wrench
• Thin blade or flat screwdriver
ClickPlug wired with 2 pairs for
daisy-chained applications
U-Bracket
Spacers
ClickPlug
SPA-UBDX100 - fits DX-S5
SPA-UBDX200 - fits DX-S8
Cable channel
W:
www.biamp.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Biamp Desono DX-S
- Page 1 • 5.5mm (or 7/32") Hex wrench • Thin blade or flat screwdriver Thread cable through the gland nut ClickPlug wired with 2 pairs for and barrel into ClickPlug daisy-chained applications (2 conductor cable shown) 9300 S.W. Gemini Drive Beaverton, OR 97008 USA www.biamp.com...
-
Page 2: Vertical Orientation
Attach the Loudspeaker to the U-Bracket 3. Remove the round caps covering the center mounting holes. Insert a thin blade into the front or rear of each end cap and pry them up. Pinch the side supports, and remove the caps. They can be discarded. 4. - Page 3 Adjust the Tap Switch 9. Rotate the tap switch knob to the desired setting before you attach the ClickPlug to the loudspeaker. Attach the ClickPlug 10. Insert the wired ClickPlug into the opening with the plug top (or side) into the indent under the safety cable loop first, then "click"...
- Page 4 ClickPlug Orientation The ClickPlug should be oriented as shown below. It can not be installed upside-down. NOTE: When mounted horizontally, the ClickPlug gland nut and U-Bracket may interfere with each other. In this instance, the ClickPlug needs to be rotated 90° to provide clearance for the U-Bracket rotation.
-
Page 5: Specifications
Black (RAL 9017) or White (RAL 9016) Color matched ABS spacer Unit Weight SPA-UBDX100: xx lbs (xx kg) SPA-UBDX100: xx lbs (xx kg) bia.mp/DX-S_pubs TECHNICAL DRAWINGS SPA-UBDX100 SPA-UBDX200 CONTACT US Email: support@biamp.com Web: support.biamp.com Warranty: biamp.com/legal/warranty-information 9300 S.W. Gemini Drive Beaverton, OR 97008 USA www.biamp.com 08NOV2022...
Need help?
Do you have a question about the Desono DX-S and is the answer not in the manual?
Questions and answers