SNMP management and the ability to record events in a file including date and time information for further analysis. The IMB2000C01 is a TL2000 terminal line module and can be housed in a two rack unit (2 RU) UR2000 mounting frame.
• Synchronization of the IMB2000C01 module is performed via any of its Ethernet interfaces using IEEE std 1588, also known as PTP, as per the specifications of the AES67 standard.
• The IMB2000C01 module and the mounting frame should always be installed, maintained, operated and removed by personnel with sufficient technical qualifications. The equipment should never be placed in damp areas, near splashing liquid, or in explosive or corrosive atmospheres.
1 - Remove the blank panel covering the front of the empty slot chosen for installing the IMB2000C01 in the mounting frame. 2 - Insert the IMB2000C01 module into the front of the mounting frame. The edges of the card slide into two plastic guides inside the mounting frame.
Albalá Ingenieros | Manual IMB2000C01 The IMB2000C01 module provides one input and one output for MADI digital audio and the electrical Ethernet interfaces. • MADI IN and MADI OUT are the input and output BNC connectors, respectively, for AES10 standard signals, better known as MADI.
Albalá Ingenieros | Manual IMB2000C01 4. OPERATION This section describes the significance of the front panel indicators of the IMB2000C01 module and their remote control and monitoring ability. 4.1. Front panel description The appearance of the front panel and the elements it contains are shown in the following illustration.
4.2. Functional description This section will describe the various interfaces and modules that form the IMB2000C01 in detail. 4.2.1. MADI encoder decoder (CODEC)
IMB2000C01, which inserts a header aligned in the M2S line and a reference signal onto the internal 13.5 MHz synchronization bus. When the IMB2000C01 is installed in a mounting frame, it always acts as the bus master. In addition to generating the header and the reference signal, it inserts audio...
DEB2008C01 must be employed. The IMB2000C01 uses the reference obtained via IEEE std 1588 to generate a 13. 5 MHz reference signal on another internal bus of the mounting frame that is used by the slave modules for synchronization.
16 streams by eight channels per stream. 4.3. Presets The IMB2000C01 provides 16 presets what are stored in non-volatile memory and can be recalled at any time via remote control with a control keyboard or through the control software installed on a PC.
Albalá Ingenieros | Manual IMB2000C01 4.4. Module remote control and supervision The IMB2000C01 requires remote control for configuration. In order to perform remote configuration and supervision of the module an optional TL2000 family remote communications controller must be installed in the mounting frame.
- Definition and recall of the presets. 4.4.1. Details of the IMB2000C01 registers The IMB2000C01 module provides control and status registers that can be read and written by means of specific commands described in the communication control module user manuals.
Page 22
Albalá Ingenieros | Manual IMB2000C01 TTL_TX 0x08 0xFF Time To Life for transmitted packets TX_SR_PORT 0x09 0xFFFF Source port OFFSET_TIME_RX 0x0B 0xFF Margin of safety before inserting samples in buffer to avoid overflow = x samples ETH_MODE_1 0x0C 0x07 Allows selecting the Ethernet operating mode...
Page 23
Albalá Ingenieros | Manual IMB2000C01 RX_1_LOST_IP_PK 0x03 0x0020 0xFFFF Lost IP packets rate = x packets RX_1_DUP_IP_PCK 0x05 0x0020 0xFFFF Duplicated IP packets rate = x packets MAX_BUFF_LEV_1 0x07 0x0020 0xFFFF Maximum buffer level = 0.01*x % MIN_BUFF_LEV_1 0x09 0x0020...
Page 29
Albalá Ingenieros | Manual IMB2000C01 VLAN_4_ID 0x0C 0x0150 0x0FFF VLAN ID STATUS Name snmp trap Description SYS_ERROR 0x00 0x0E System error. (Irrecoverable alarm or event) 0=OK PTP_INT_SELECTED 0x00 0x40 PTP interface selected 0=Ethernet 1,1=Ethernet 2 TX_WORKIN_STAT_1 0x02 0x02 TX 1 transmitting...
Page 30
Albalá Ingenieros | Manual IMB2000C01 RX_TIME_RST 0x15 0xFFFFFF Elapsed time since last reset = x s LINK_1 0x18 0x0B Ethernet conection status 8=10Mbps, 9=100Mbps, 10=1Gbps, ?=No link SYSTEM_1 0x18 0x0C Ethernet conection system 3=Full Duplex, 2=Half Duplex, ?=No link LINK_2...
Albalá Ingenieros | Manual IMB2000C01 5. GLOSSARY AES/EBU This acronym covers the combined AES and EBU standard for transmission of digital audio. The standard defines a serial interface known as AES3 as per AES, EBU 3250-E as per EBU or ITU-R BS.647-2 as per ITU. The interface originally transmitted two channels (one pair) with PCM coding with a bit depth of 20 or 24 bit and a sampling frequency between 32 kHz and 192 kHz.
Albalá Ingenieros | Manual IMB2000C01 6. REGULATIONS AES10 (2008) AES recommended practice for digital audio engineering - Serial Multichannel Audio Digital Interface (MADI) See also: AES10id AES67 (2018) AES standard for audio applications of networks - High-performance streaming audio-over-IP interoperability.
Need help?
Do you have a question about the IMB2000C01 and is the answer not in the manual?
Questions and answers