Subscribe to Our Youtube Channel
Summary of Contents for DOCYKE GK-06
- Page 1 额定功率 / Motor power : 400W 电池配置 / Battery capacity : 18V=6Ah 充电时间 / Charging time : 2-3h GO-KART KIT 安装时间 / Time to bulid : 6-20 hours 最大载重 / Max load : 50kg 卡 丁 车 套 件 产品净重 / Net weight : 30kg 续航时间...
- Page 2 目 录 Contents 注意事项 Warning GK-06 安装步骤 5-32 GK-06 assembly drawing GK-06 快速安装图 GK-06 diagram...
- Page 3 We recommends that you review and reinforce the information in this manual periodically with younger riders，inspect and maintain your DOCYKE rides to insure their safety. The rides and all the parts have been tested by official independent testing agencies.
- Page 4 Dirt，1eaves，and other debris can damage， shrink，expand or weaken docyke parts. Keep your ride in a dry environment. 7) 多可 除螺钉外其余都为特别设计的零件 , 请不要和市场上类似零件混用。 Most of the docyke's components are specially designed, please do not mix with similar parts on the market. 8) 检查充气轮胎气压不能大于 1.8bar(1.8 kgf/cm²) Check the air pressure in the tires to max 1.8bar.
-
Page 5: Recommended Tools
1) 充电器仅中室内使用 , 并使充电及使用环境的清洁 , 干燥。不得暴露在潮湿 , 粉尘环 境中 , 否则会增加电击危险。 The charger is only used indoors, Keep work area clean and well lit. Do not expose DOCYKE to rain or wet conditions. 2) 只能用多可制造商规定的充电器及电池进行充电 . - Page 6 GK-06 PART PART PART PART...
- Page 7 PART PART 1-1 PART 1-2...
- Page 8 PART 1-1 The positioning blocks are some of the smallest parts but they also some of the most important.Putting them in the right place is a key of the product. 产品中一共包含两种定位块，它是至 关重要的部件，请仔细分辨。几乎所有零 件的装配都会使用到他们，请务必按照说 明使用，避免漏装或误装。 M8x25 280mm M6=2 240mm M8x25 M6x35=2 连接后拧紧两个螺丝。...
- Page 9 注意零件上下方向。 Pay attention to the up and down direction of parts. M8x20=2 M8x25...
- Page 10 ∅ 22x ∅ 32xh5=3 M8x20=2 172mm ∅ 8x ∅ 30xh2=2 M6x20=2 M6x14=4 M8x25 螺丝在不同位置需要使用不同长度，请务必按 照指导手册使用，同时使用六角柄拧紧螺丝。 Screws are required to use different lengths in different locations, so be sure to follow the instruction manual and use the Hex wrench handle to tighten the screws.prevent them coming loose.
- Page 11 PART 1-2 80mm M8x20=2 装配时螺钉必须拧紧。 M8x20 Tighten the bolts with full force to prevent them coming loose. 20mm M8x25...
- Page 12 M8x60 140mm 220mm M8x20...
- Page 13 PART PART 2-1 PART 2-2...
- Page 14 PART 2-1 装配时螺钉必须拧紧。 Tighten the bolts with full force to prevent them coming loose. M8x25 360mm M6=2 60mm M8x25 M6x35=2 连接后拧紧两个螺丝。 Tighten the two screws after connection.
- Page 15 M8x20=2 200mm M8x20=2 如图， 对称组装共 2 个。 As shown in the figure, assemble 2 components. M8x60 20° 每格为 10°， 最高精度为 5° （半格） 。 Each mark is 10° , and the maximum accuracy is 5 ° (half mark).
- Page 16 PART 2-2 M8x20=4...
- Page 17 PART PART 3-1 M8x25 320mm M6=2 140mm M8x25 M6x35=2...
- Page 18 连接后拧紧两个螺丝。 Tighten the two screws after connection. 注意零件上下方向。 Pay attention to the up and down direction of parts. M8x20=2 120mm M8x20=2...
- Page 19 M8x20=2 M8x20=3 140mm 40mm...
- Page 20 M8x20=2 120mm 55° M8x32...
- Page 21 ASM. ASM.1 20°...
- Page 22 M8x32=2 M8=2 ASM.2 M8x25 如图， 对称组装各 2 个。 As shown in the figure, assemble 2 symmetrically.
- Page 23 M8x25 M8x32=2 如图， 对称组装共 2 个。 As shown in the figure, assemble 2 components. M8=2 M8x20=2 13.2mm 16mm...
- Page 24 ASM.3 20° 15° M8x32=2 M8=2...
- Page 25 PART PART 4-1 M8x20=2...
- Page 26 M8x20=2 M8x20=2...
- Page 27 T34 Belt Wheel (Fixed) Ø22x ∅ 32xh5=2 M8x20=2 222mm ∅ 8x ∅ 30xh2=2 ∅ 22x ∅ 32xh2=2 936mm...
- Page 28 ∅ 8x ∅ 30xh2=2 ∅ 22x ∅ 32xh10=5 M8x20=2 418mm Ø22Xø32xh40=2 Ø22x ∅ 32xh5 Ø22x ∅ 32xh2...
- Page 29 PART 4-2 M8x20...
- Page 30 M8x20...
- Page 31 固定线缆。 Fix the cable.
- Page 32 应用于 P9 H 处。 Applied at P9 H. 如果您有任何问题， 或者更好， 更酷的创意， 欢迎联系我们。 If you have any questions, better ideas, or join our team, welcome to contact us. do@docyke.com...
Need help?
Do you have a question about the GK-06 and is the answer not in the manual?
Questions and answers