Advertisement
4. OPERATION
4.1.
USING THE WRENCH
4.1.1.
Fit a suitable socket to the wrench by snapping it onto the square drive.
4.1.2.
Fit the battery pack to the wrench by aligning the tongue on the battery with the groove in the housing and slide into place. Ensure
that the battery pack is firmly located, A click will be heard when it has locked into position.
4.1.3.
BATTERY CHARGE INDICATOR LEDs
4.1.4.
Once the battery has been fitted a gentle push on the trigger will illuminate the battery charge indicators. They will turn off
after a few seconds if the tool is not being used.
4.1.5.
Select the required direction of rotation. To change direction, turn the direction selector on the rear of the drive head, to the left or
right.
right. DO NOT
DO NOT attempt to change the direction of rotation whilst trigger is depressed.
attempt to change the direction of rotation whilst trigger is depressed.
4.1.6.
4.1.6.
Speed can be controlled by varying the finger pressure on the trigger. Initial pressure will switch on the worklight.
4.1.7.
The trigger can be locked in the off position when required to prevent accidental use.
4.1.8.
When tightening, take care not to over-torque small fixi
When tightening, take care not to over-torque small fixings.
Note: On critical fixings always check the torque with a torque wrench according to the product or vehicle manufacturer's
guidelines.
This tool may cause Hand Arm Vibration Syndrome if its use is not managed adequately.
This tool is subject to the vibration testing section of the Machinery Directive 2006/42/EC.
This tool is to be operated in accordance with these instructions.
Measured vibration emission value (a)...........................7.373.m/s²
Uncertainty value (k):......................................................1.5 m/s²
Please note that the application of the tool to a sole specialist task may produce a different average vibration emission. We
recommend that a specific evaluation of the vibration emission is conducted prior to commencing with a specialist task.
A health and safety assessment by the user (or employer) will need to be carried out to determine the suitable duration of use for
each tool.
N B: Stated Vibration Emission values are type-test values and are intended to be typical.
Whilst in use, the actual value will vary considerably from and depend on many factors.
Such factors include; the operator, the task and the inserted tool or consumable.
NB: ensure that the length of leader hoses is sufficient to allow unrestricted use, as this also helps to reduce vibration.
The state of maintenance of the tool itself is also an important factor, a poorly maintained tool will also increase the risk of Hand
Arm Vibration Syndrome.
Health surveillance.
We recommend a programme of health surveillance to detect early symptoms of vibration injury so that management procedures
can be modified accordingly.
Personal protective equipment.
We are not aware of any personal protective equipment (PPE) that provides protection against vibration injury that may result from
the uncontrolled use of this tool. We recommend a sufficient supply of clothing (including gloves) to enable the operator to remain
warm and dry and maintain good blood circulation in fingers etc. Please note that the most effective protection is prevention, please
refer to the
Correct Use and Maintenance section in these instructions. Guidance relating to the management of hand arm vibration can be
found on the HSC website www.hse.gov.uk - Hand-Arm Vibration at Work.
WEEE REGULATIONS
Dispose of this product at the end of its working life in compliance with the EU Directive on Waste Electrical and Electronic Equipment
(WEEE). When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid
waste authority for recycling information.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to
a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely
unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids
according to local regulations.
Note: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior
notice.
Important: No Liability is accepted for incorrect use of this product.
Warranty: Guarantee is 36 months from purchase date, proof of which is required for any claim.
Sealey Group, Kempson Way, Suffolk Business Park, Bury St Edmunds, Suffolk. IP32 7AR
01284 757500
© Jack Sealey Limited
change direction, turn the direction selector on the rear of the drive head, to the left or
WARNING! – Risk of Hand Arm Vibration Injury.
01284 703534
sales@sealey.co.uk
Original Language Version
www.sealey.co.uk
CP1209 Issue 2 (2) 05/09/22
Advertisement
