Table of Contents
Advertisement
Long Term Storage Instructions
It is EXTREMELY IMPORTANT to clean the machine and remove all formula powder residue before storage.
If you're going to store your Formula Pro® Mini for later use, or will not use it for a while, please follow the
instructions below:
1. Remove the powder container parts, funnel, funnel cover, drip tray and water tank from the base.
2. Wipe the base with a clean damp cloth and make sure to remove any and all formula residue. Dry the base well.
3. Empty the powder container, wash all powder container parts, dry thoroughly, reassemble, & reinstall on the base.
4. Follow the Monthly Descaling Instructions on page 12, steps 1-7 only. Do not remove or re ll the water tank after
step 7.
5. Remove the water tank and turn the base of the machine upside down over a sink. Water will drain from the
vent hole in the top/back of the machine. You can press the spring-loaded valve on the base where the water
tank connects to let air in, and all water out of the machine.
6. Unplug the machine, remove the funnel, funnel cover and water tank, dry them both thoroughly and reinstall
them on the machine.
7. Your machine is now ready for storage. Pack the machine in its box, or enclose it in a bag to keep it dust free.
Error Codes
In the unlikely event of electrical component error or interruption during operation, the following codes will
be displayed on the LCD screen. Pressing and holding the power button will clear the code and operation should
return to normal. If the code returns or is unable to be cleared, please contact Baby Brezza Customer Service.
Indicates an operation error of the motor that turns the powder container parts.
Contact Baby Brezza Customer Service.
Indicates an operation error of the motor sensor that detects the rotation of the measuring wheel.
Contact Baby Brezza Customer Service.
Indicates an operation error of the water ow meter that measures the water volume output.
Contact Baby Brezza Customer Service.
Indicates an operation error of the temperature sensor that measures water temperature.
Contact Baby Brezza Customer Service.
Indicates an operation error of the water level switch that measures the water remaining.
Contact Baby Brezza Customer Service.
Indicates that hot water has been poured into the water tank and entered the machine.
Empty the water tank, re ll it with room temperature water, return it to the base and wait for the
water inside the machine to cool. Press & hold the power button to clear the code.
Indicates that the powder container lid has been opened during operation. Make sure the powder container
lid is completely closed, press & hold the power button to clear the code. The machine will return to normal.
Indicates that the funnel has been removed during operation. Make sure the funnel & funnel cover are
Installed correctly, press & hold the power button to clear the code. The machine will return to normal.
13
Troubleshooting
Condition
Possible Cause
Machine will not start.
Machine is unplugged.
Machine is not turned on.
Funnel is removed or not fully inserted.
Water level is below "MIN" line.
Powder container is removed or not fully seated.
Powder container lid is not completely closed.
Powder container lid is on backwards.
Water in Water Tank is too cold.
( Temp Symbol on LCD Flashing)
Water in Water Tank is too hot.
( Temp Symbol on LCD panel is ashing)
Temperature of dispensed
Water has not yet been heated to
formula is too cold.
correct temperature.
Funnel will not t all the way
Funnel cover is not straight on funnel and/or
in Funnel Compartment.
not pushed down completely.
Clean Funnel symbol is on, Formula Pro
Funnel and hole on underside of
beeps when start button is pressed.
Powder Container require cleaning.
Too much powder dispensed.
Locking cover is not installed correctly.
Incorrect powder setting selected.
Not enough powder dispensed.
Powder level in powder container is too low.
Machine has not been cleaned well.
Silicone scraper is not installed correctly.
Incorrect powder setting selected.
Not dispensing water.
Water Tank not fully seated.
Powder build-up on funnel cover &
Frequent use without cleaning underside of
underside of powder container.
powder container. See page 11 for details.
If you can not remedy problems by using the troubleshooting chart above, do not return your Formula Pro® Mini to the store.
Please contact Baby Brezza Customer Service at 1-888-396-6552 or visit babybrezza.com for videos.
Possible Remedy
Make sure the plug is securely inserted into the power outlet.
Press Power Button to turn on machine.
Insert funnel or push front of funnel until ush with machine.
Add more water to water tank.
Make sure powder container is placed on base properly.
Turn Powder container lid clockwise to close completely.
See page 7, step 2 for details.
Make sure tab on edge of Powder Container Lid is facing
the back of the machine and engaged with safety switch.
See page 7, step 2 for details.
Wait for water to warm up to body temperature.
Wait for water to cool down.
Wait for heater to warm water. Make sure temperature
symbol stays on solid instead of ashing.
Align tab on front of Funnel Cover with notch in Funnel
and push down Funnel Cover completely.
Follow Steps on Page 11 to clean and dry Funnel and hole on
underside of Powder Container.
Check locking cover and make sure the front edge is locked
under the tab in the powder container.
See page 6, step 6 & 7 for details.
Make sure to select the correct setting number for your
powder type. For details, go to: babybrezza.com/settings
Re ll Powder Container with more powder.
Disassemble, clean by hand-washing, completely dry all parts
and reassemble.
Make sure silicone scraper is installed correctly.
Go to: babybrezza.com/settings to con rm setting for your
powder brand and type, then choose correct setting using
the "powder setting" button on the control panel.
Push Water Tank down all the way on Base.
Clean funnel, funnel cover and underside of
powder container every 4 bottles.
14
Advertisement
Table of Contents
