Related Manuals for Valley Tool Vrisimo LP2084
Summary of Contents for Valley Tool Vrisimo LP2084
- Page 1 Orchard Low Profile Series PO Box 220 | 2507 Tully Road | Hughson, CA 95326 | 800-426-5615 w ww.valleyto o lmfg .co m...
-
Page 3: Table Of Contents
Orchard Low Profile Series Table Of Contents Introduction Thank You Warranty Safety Operational Safety Maintenance Safety Basic Operation Attaching to Power Unit Starting / Running / Shut Down Adjustments & Maintenance Cut Height / Wear Components / Cleaning Lubrication 9-10 Transport Transport / Removal / Storage Questions... -
Page 4: Thank You
Vrisimo Flail Mowers & Shredders is solely owned by Valley Tool and Manufacturing. Have industrial applications? Own a skid steer or mini excavator? For our full line of industrial equipment visit: www.valleytoolmfg.com... -
Page 5: Warranty
& Mfg. warrants each product to be free from at Valley Tool & Mfg., of Hughson CA, or at a service manufacturing defects, subject to the limitations facility designated by us, or such part or parts as contained in this policy. -
Page 6: Safety
Safety Failure to heed any of these warnings may result in Operate at a safe speed (typically 0-5 mph) in personal injury or death. consideration of the local terrain, moving slower when operating on or near slopes, ditches or drop- A. -
Page 7: Maintenance Safety
Safety Be aware of the risks of equipment and grass fires. Maintenance should only be performed by properly To mitigate those risks: trained individuals. It is the owner’s responsibility to ensure all individuals involved in maintaining the • Do not smoke or have an open flame in the work machine are properly trained in the appropriate area. -
Page 8: Basic Operation
Basic Operation A. Attaching to the Power Unit B. Starting Procedure The person that is attaching your Vrisimo product 1. Check that the attachment is in the down posi- should be familiar with the attachment and remov- tion and that the blades are not in contact with al of equipment from a 3-point hitch and be able to ground. - Page 9 Basic Operation Adjustable Top Link Pin Lift Arm Pin Skid Shoe Back Roller Mount Plate C. Running Your Attachment D. Shut Down Procedure 1. Determine ground speed based on terrain and 1. When work is completed, disengage the PTO material being cut. This will typically fall within shaft and position it for storage or transport the 0-5 mph range.
-
Page 10: Adjustments & Maintenance Cut Height / Wear Components / Cleaning
Adjustments & Maintenance Note: Before performing maintenance, ensure all 2. Replacing the complete knife assembly is done motion has stopped and that the Power Unit is by removing the hanger rod. Re-insert hanging powered down with ignition key removed. Before rod inserting a new knife assembly at each working on or underneath the mower, place blocks on station. - Page 11 Adjustments & Maintenance Quick Connect Hanger Scoop Knives Bottom Pulley Top Pulley D-Ring Hanger Rod Belt Tension Cutter Drum / Knives Tension Adjustment Gearbox PTO Shaft Top Pulley Bottom Pulley Top Shaft Cut Height Adjustment Backroller Adjustment www.vrisimo.com...
-
Page 12: Lubrication
Top Shaft Bearings NLGI 1.5 ISO VG460 zerk on each side of the mower. NLGI 1.5 ISO VG460 Backroll Bearings 2. Valley Tool recommends greasing with NLGI 2 NLGI 1.5 ISO VG460 Driveshaft Yokes VG100. Any lithium based NLGI Grade 2 NLGI 1.5 ISO VG460... - Page 13 Adjustments & Maintenance Maintenance Locations Grease Viscosity vs. Temp We understand that you have a lot of options when it comes to choosing your grease. Blue Group Any selection from the of greases are equivalent, and Orange Group any selection from the of greases are equivalent.
-
Page 14: Transport / Removal / Storage
Transport, Removal and Storage E. Transport, Removal and Storage 3. Removal Disengage PTO and shut off engine allowing all • Place attachment on ground with entire weight movement to stop before leaving the operators resting on mower. position to adjust, lubricate, clean or unclog the •... -
Page 15: Frequently Asked Questions
Frequently Asked Questions Q. When I am replacing gear oil, how much should Q. How do I reverse cutter drum rotation? I add? A. To reverse cutter drum rotation, un-mount the A. When replacing gear oil, fill from the Upper gearbox from its default position, remove the Fitting. - Page 17 Orchard Low Profile Series Parts Book www.vrisimo.com...
- Page 18 www.vrisimo.com...
- Page 19 www.vrisimo.com...
- Page 20 www.vrisimo.com...
- Page 21 www.vrisimo.com...
- Page 22 www.vrisimo.com...
- Page 23 www.vrisimo.com...
- Page 24 www.vrisimo.com...
- Page 25 www.vrisimo.com...
- Page 26 www.vrisimo.com...
- Page 27 www.vrisimo.com...
- Page 28 www.vrisimo.com...
- Page 29 www.vrisimo.com...
- Page 32 REVISION: LPV3-220831 PO Box 220 | 2507 Tully Road | Hughson, CA 95326 | 800-426-5615 ww w.val leyto o lmfg .com...