EDIFIER MP280 - Portable Speaker Manual

Box contents

Charging the battery

Charge indicator
When charging: red light on
Full charged: no light
Power level indicator
When charging: running light
Full charged: light stays constant

1. When charging and the speaker is turned on, the power level indicator will blink and travel up. When charge is complete, the indicator lights will remain lit. While charging, when the speaker is turned off, only the charge indicator will remain constant.
2. For best speaker performance, please check the battery level before each use.
3. To ensure a full charge and for optimal audio playback, please fully charge the speaker once a month.
4. Please turn off the speaker when not in use.

Note:

1. When the speaker has no audio source input while it is switched on, it will turn off automatically after 10 minutes.
2. You will also hear an indicator tone when the speaker is turned on, connected or disconnected from a Bluetooth device, and when the battery voltage is low.
3. Battery playback time (offers up to approximately 10 hours) may vary from music sources and volume settings.

Illustration

1. Audio source selector/Power level display
   Audio source selector: press once
   Power level display: press and hold
2. ON/OFF: Press and hold
3. LED indicator:
   Green: Line In
   Blue: Bluetooth
   Red: microSD card
4. NFC (Near Field Communication) receiver
5. Play/Pause/Display power level
6. Volume down/Previous track
   Volume down: press once
   Previous track: press and hold (Bluetooth/microSD card mode)
7. Volume up/Next track
   Volume up: press once
   Next track: press and hold (Bluetooth/microSD card mode)
8. Power level indicator

9. DC output (5V-500mA)
10. LINE IN input port
11. Charging indicator
12. DC input port
13. microSD card slot

Connections

1. Turn on speaker
2. On your device (mobile phone, tablet device, MP3/MP4 player etc.), go to Bluetooth to search and select "EDIFIER MP280 Connect".
3. Pair your device with "EDIFIER MP280 Connect".
4. Press play on your device and adjust volume to a desired level. 5.To disconnect Bluetooth: Press & hold

Note:

1. Bluetooth connectivity and compatibility may be different between different source devices, depending on the software version of the source.
2. To enjoy the full Bluetooth functions of this product, please ensure your mobile device has A2DP/HFP profile.
3. PIN code for connection is "0000" if needed.
4. In Bluetooth mode, "previous/next track" is ideal for supporting AVRCP (Audio/Video Remote Control Profile) protocol device.
5. In Bluetooth mode, the speaker power level will display on some phones when connected (*Apple and Xiaomi phones are compatible).

NFC (Near Field Communication) function

1. Turn on speaker
2. Switch on NFC function on your device.
3. Place your device near the speaker. NFC will connect to Bluetooth automatically. Your device is now connected to the speaker.
4. Press play on your device and adjust the volume to a desired level.

Disconnect:
You can switch off NFC function after Bluetooth is connected, and the speaker will remain connected via Bluetooth.

Spare power source output/ Battery power output

The USB output can be used to charge your mobile device using the available USB cable.

Specifications

Power output	RMS 4W x 2
Signal to noise ratio	80dBA
Frequency response	75Hz~18KHz
Input sensitivity	800 ± 50mV
Input type	LINE IN/Bluetooth/microSD card
Speaker driver	1 3/4 inch (48mm)

Troubleshooting

• Switch the EDIFIER MP280 off then on and reconnect to the audio source.
• Ensure Bluetooth function is enabled on your Bluetooth devices.
• Move the devices closer and retry the connection.
• Try another Bluetooth device for connection.
• Switch the system off then on and reconnect to the audio source.
• Confirm that the system is ON and not in STBY mode.
• Check the master volume and confirm that it is turned up.
• Check audio source to confirm that it is functioning properly.

For warranty information regarding your new purchase please visit www.edifier.com
If you have any further questions or concerns regarding EDIFIER Products anywhere in the world. please visit our website at: www.edifier.com
or email EDIFIER Support for further assistance at: main@edifier.com.
To contact us by phone : 1-877-EDIFIER (334-3437) in US and Canada; for South America: Please visit www.edifier.com (English) or www.edifierla.com (Spanish/Portuguese) for detailed local contact information.

NFC Forum and the NFC Forum logo are trademarks of the Near Field Communication Forum.