PPA INTERRUPTOR T2 TOUCH SMART - Controller Manual

INTRODUCTION

Do not use the equipment without referring to this manual first.

The smart wi-fi touch switch has a touch sensor and a beautiful modern design with a glass mirror. Possibility of using one or two lamps, it accepts commands via the touch of the switch or via the "PPA ON" application, all with visual feedback via the equipment's LED.

TECHNICAL CHARACTERISTICS

ELECTRICAL CONNECTIONS DIAGRAM

TABLE OF POWER (LOAD) LIMITS FOR EACH OUTPUT OF THE TOUCH SWITCH

NOTE: For any other application other than lighting control, such as controlling a fan, automated blind, among other purposes, the maximum load suggested is 5A.

REGISTRATION OF THE SWITCH ON PPA ON APP

Introduction to the app:
Step 1: To download the "PPA ON" app, go to the Play Store or App Store app store.
NOTE: The application is not available for Windows Phone operating system (Micrisoft) and other operating systems on the market, except the two mentioned above.
Step 2: Login if you already have an account, if not, register in the application by entering the necessary information, after registration, click on "get verification code".

NOTE: Before registering the switch in the application, do this procedure with the equipment turned on

Step 3: Add a device, for this and turn off mobile data connect your Smartphone to the 2.4GHz Wi-Fi network that the device will be connected to. Turn on Bluetooth, turn on device location click '+' in the upper right corner.

Step 4: Enter the WiFi network and password the device will connect to. Click next.

ATTENTION!! IF THE DEVICE REGISTRATION PROCEDURE THROUGH THE EZ MODE IS NOT SUCCESSFULLY CARRIED OUT, IT WILL BE NECESSARY TO REGISTER THROUGH THE AP MODE.

Step 5: Enter add device again. Enter the Wi-Fi network and password the device will connect. Click next.

Make sure your device is reset, to enter AP Mode (LED flashing slowly 1 me per second), tap EZ Mode in the app to change the mode. If not reset, press and hold the reset bu on un l the LED flashes slowly.

After connecting to the switch, the App will ask you to login to the local network (Smartlife-XXXX) that it will make available, a er connec ng to the local network, go back to the applica on to con nue the switch registra on.

Your device has been successfully added, then tap Done.

Okay, now you can use your smart wi-fi touch switch through the app.

GENERAL TERMS AND CONDITIONS OF WARRANTY

MOTOPPAR da Amazônia Indústria e Comércio de Eletrônicos Ltda, registered with CNPJ No. 09.084.119/0002-45, located at Praça Linear, No. 100, Bloco II, Centro, Santa Rita do Sapucaí/MG, CEP 37.500-000, manufacturer of the PPA and CITROX products, guarantees this device against defects in design, manufacture, assembly and/or jointly and severally as a result of defects in the quality of the material that make it inappropriate or unsuitable for the consumption for which it is intended, for a legal period of 90 (ninety) days from the date of purchase, provided that the installation guidelines described in the instruction manual are observed.
As a result of the credibility and trust placed in PPA AND CITROX products, we added another 275 days to the above period, reaching a total of 1 (one) year, also counted from the date of purchase to be proven by the consumer through the proof of purchase (Supervisor Note).
In the event of a defect, within the warranty period, the liability of PPA and/or CITROX is restricted to the repair or replacement of the device manufactured by it, under the following conditions:

1. The repair and readjustment of the equipment can only be carried out by the Technical Assistance, which is qualified to open, remove, replace parts or components, as well as repair the defects covered by the warranty, and, in the absence of this and any use of parts not originals contained in the use, will result in the waiver of this term by the consumer;
2. The warranty will not extend to accessories such as cables, screws kit, fixing brackets, sources, etc.;
3. Expenses for packaging, transport and reinstallation of the product are exclusively borne by the consumer;
4. The equipment must be sent directly to the company responsible for the sale, representative of the manufacturer, through the address on the purchase invoice, properly packaged, thus avoiding the loss of warranty;
5. The replacement or repair of the equipment does not extend the warranty period.

This warranty will be void if the product:

1. Suffer damages caused by agents of nature, such as atmospheric discharges, floods, fires, landslides, etc.;
2. It is installed in an improper electrical network or even in disagreement with any of the installation instructions set out in the manual;
3. Defects caused by falls, blows or any other physical accident;
4. For violation of the equipment or attempt to repair by unauthorized personnel;
5. It is not used for its intended purpose;
6. Not used under normal conditions;
7. Suffer damage caused by accessories or equipment attached to the product.

Recommendation:
We recommend the installation and maintenance of the product by a specialized technical service.
If the product has a defect or abnormal operation, look for a specialized Technical Service for the necessary corrections.

Made by:
Motoppar da Amazônia Indústria e Comercio de Eletrônicos LTDA
Praça Linear, 100, Bloco 2 - Centro
Santa Rita do Sapucaí - MG - CEP 37540-000 - Brasil
CNPJ: 09.084.119/0002-45 www.ppa.com.br | +55 14 3407 1000