Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for OSKA 3 Auto Series
Summary of Contents for OSKA 3 Auto Series
- Page 1 User Guide Series3 Auto Version 3: 17.11.2022...
-
Page 2: Table Of Contents
Contents Know your symbols Know your symbols Important safeguards Manufacturer Do not iron Statements Introduction Foot end Tumble dry Package contents Product function CE marked Do not dry clean System installation Operation General Catalogue number Resistant to ignition CPR function Pressure set up Authorized EC Wipe down... -
Page 3: Important Safeguards
Introduction Package contents This manual should be used for the initial set up of Check inside the package. If any of the following Important safeguards into water. Return the product to a service the system and for reference purposes. items should be missing or damaged, please centre for examination and repair. -
Page 4: Product Function
Product function Power Switch(1) Alternate mode(5) Pump Unit • The switch is at the right side • Press to set the air mattress The functions of the pump for Series3 Auto are of the pump. in alternate therapy mode. as follows: • Turn ON/OFF the power and press Power button Static mode(6) on the panel, the pump will start/stop operation. -
Page 5: System Installation
Also make • DO NOT change any component by yourself. adjustable straps under each end of your bed. sure this product is well grounded. If there is need for replacement or repair, Ensure buckles are securely fastened and straps always contact OSKA Care are pulled tight. d) Switch the power button on. Allow up to 40 minutes for full inflation. For patients: When the pressure has been adjusted to a desired level of firmness, the patient can then lie on the mattress. -
Page 6: Cpr Function
CPR function Power failure NOTE: Please follow instructions below for In case there is a bad connection of detailed operating procedure of each type. tubing or any air leakage from the mattress, this will result in a low pressure When there is an emergency requirement to If the power is cut, only the power failure alarm Step 1 Turn on the power. -
Page 7: Cleaning
Environment requirements Maintenance Cleaning wetting with any liquid disinfectant. • Any obvious blood spots should be wet In this section, we describe the procedures to clean thoroughly with 1:9 Hypochiorite solution (1 Operating Conditions General and decontaminate the pump. It is important to part bleach to 9 parts water) and allow drying • Ambient Temperature: 5°C~40°C • Check the power cord and plug to see if there follow these procedures before using the system for at least 10 minutes. - Page 8 Troubleshooting guide Troubleshooting guide continued Problems Reasons Maintenance Problems Reasons Maintenance Pump does not work. 1. After powered on, check if visible LED Mattress has pillow One way valve is assembled Assemble the one way valve light turns on. If not, please check the function, but air cell fail to reversely.
-
Page 9: Specifications
Notes Specifications Technical Specifications Pump Mattress Item: Series3 Auto Pump Item: Series3 Auto Mattress Power supply: 220V/50Hz, 1A Size: 203cm(L) x 90cm(W) x 20cm(H) Air output: 8 litre/min. Top cover: Nylon / PU with zipper Pressure range: 20 mmHg – 55 mmHg Air cells: Nylon PVC / Nylon TPU / TPU Cycle time: 10/15/20/25 min. Base: Durable Nylon / PVC 840D Case Material: Flame Retardant ABS 20 x 8’’... - Page 10 Notes Notes Series3 Auto User Guide...
- Page 11 Pressure Care Experts Edward House, 5 Penner Road, Havant, PO9 1QZ 02394 318 318 | ask@oska.uk.com oska.uk.com Series3 Auto User Guide...
Need help?
Do you have a question about the 3 Auto Series and is the answer not in the manual?
Questions and answers