Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Interpump Hydralok HCLMOBILE
Summary of Contents for Interpump Hydralok HCLMOBILE
- Page 1 USER MANUAL Electric hose cutting machine HCLMOBILE...
-
Page 2: Table Of Contents
SOMMARIO WARRANTY CONDITIONS ....................3 DECLARATION OF CONFORMITY ..................4 SAFETY REGULATIONS ....................5 TECHNICAL / DIMENSIONAL DATA .................. 6 HANDLING/TRANSPORT ....................6 INSTALLATION ........................6 PRELIMINARY CHECKS ..................... 7 LIGHTING ..........................7 ROUTINE MAINTENANCE ....................7 MACHINE DESCRIPTION ....................7 OPERATING INSTRUCTIONS .................... -
Page 3: Warranty Conditions
WARRANTY CONDITIONS 1. Note that all machines undergo strict testing before shipment. 2. All machines are warranted against any defects for a period of 12 MONTHS starting from the date of delivery to the customer. The company reserves the right to require a copy of the sales invoice. -
Page 4: Declaration Of Conformity
DECLARATION OF CONFORMITY (according to current EC legislation) the subscribed: I.M.M. Hydraulics S.p.A. registered office in: Via Italia 49, 51 66041 ATESSA VAT and fiscal Code 01427010697 in the person of Marcello Di Campli declares: Model: HCLMOBILE Construction Year: 2019 Serial Number: Description: Electric hose cutting machine... -
Page 5: Safety Regulations
SAFETY REGULATIONS Always work in safe conditions and with the necessary space around the machine. Ensure that the machine is placed on a stable and appropriate working surface. 1. DO NOT USE the equipment before reading the user manual. 2. CAUTION! If improperly used, the equipment may be dangerous and may cause injury. -
Page 6: Technical / Dimensional Data
TECHNICAL / DIMENSIONAL DATA TECHNICAL/DIMENSIONAL DATA HCL MOBILE 3/16” -1 1/2” Capacity R1AT/1SN/R2AT/2SN (2 wire) 3/16” -1 1/4” R9R/4SP (4 wire) Motor [Kw] Dimensions [mm] Ø 250x3 Gross Weight [kg] Volts [V] 12 / 24 VDC Noise level < 75 dB HANDLING/TRANSPORT The machine will normally be shipped bolted to a wooden pallet. -
Page 7: Preliminary Checks
PRELIMINARY CHECKS Place the machine on a stable surface. Where applicable, ensure that the power supply line is fitted with a differential safety breaker and overload cutout. LIGHTING The equipment does not have its own lighting and so it must be used in a suitably illuminated area. -
Page 8: Maintenance And Service
MAINTENANCE AND SERVICE Regular inspection and routine cleaning of the machine, focussing especially on the guards (Appendix 3 ‐ 7 & 8). Under no circumstances should the machine be used if the guards have been damaged or removed. The cutting blade should be inspected regularly for signs of wear or damage. DANGER! The machine must not be run if the blade shows signs of damage or stress cracking as projectiles may cause serious injury as the blade rotates at very high speeds. -
Page 9: Appendix 1 - Mounting Information
Appendix 1 – Mounting Information All dimensions in mm. -
Page 10: Appendix 2 - Wiring Schematic
Appendix 2 – Wiring Schematic... -
Page 11: Appendix 3 - Machine Diagram
Appendix 3 – Machine Diagram... -
Page 13: Appendix 4 - Blade Replacement Instructions
Appendix 4 – Blade Replacement Instructions The following instructions detail how to change the cutting blade of the HCL mobile Cutter. DANGER! Cutting blades are extremely sharp and must be handled with extreme care at all times to avoid injury. Remove four M6 dome head bolts from the front guard (two each side) and the M4 bolt at the top of the front guard, as shown above. - Page 14 Remove the two M6 socket cap bolts from the pivot block as shown above. Note! that the tension within the handle spring will attempt to work against this operation during undoing. Pivot the handle, and pivot linkages, the cutting jaws, and the pivot block up above the rear cover as shown below.
- Page 15 Remove the M6 clamp plate bolts (x2) by locating a bar or hex key into the torsion restraint holes in the blade boss, shown above. Once both bolts have been removed the clamp plate can be removed and the blade can be carefully removed and replaced as shown below ensuring that the teeth are pointing in the correct direction.
-
Page 16: Spare Parts
SPARE PARTS Part No. Description CHBL250325D Toothed blade 250x3x25mm, incl. adapter 40/25mm CHBL250325 Smooth blade 250x3x25mm, incl. adapter 40/25mm...
Need help?
Do you have a question about the Hydralok HCLMOBILE and is the answer not in the manual?
Questions and answers