1. Manuals
  2. Brands
  3. djm direct Manuals
  4. Drill
  5. DJMBD13-40
  6. Original operating manual

djm direct DJMBD13-40 Original Operating Manual

Bench drill
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Item No.:DJMBD13-40
Bench Drill
BENCH DRILL
Original Operating Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DJMBD13-40 and is the answer not in the manual?

Questions and answers

Summary of Contents for djm direct DJMBD13-40

  • Page 1 Item No.:DJMBD13-40 Bench Drill BENCH DRILL Original Operating Manual...

  • Page 2: Device Description

    1.Introduction 2.Device Description MANUFACTURER: 1. Gear Cover 2. ON/OFF Switch DJM Direct.com 3. Motor Unit 43 Churchill Way, 4. Column Tube Lomeshaye Industrial Estate, 5. Drilling Bench Holder Nelson, Lancashire BB9 6RT UK 6. Locking Handle DEAR CUSTOMER 7. Base Plate We hope your new tool brings you much enjoyment 8.
  • Page 4 3. Unpacking Protect eyes, face, and head from objects that may be thrown from the unit. Always wear safety goggles or ●Open the packaging and remove the device carefully. safety glasses with side shields when operating. ●Remove the packaging material as well as the Wear appropriate hearing protection.

  • Page 5: Specific Safety Rules

    Do not use the cable for purposes for which it is not • Take care of your tools. Keep cutting tools sharp intended. Do not use the cable to pull the plug out of and clean in order to be able to work better and more the outlet.

  • Page 6: Technical Data

    6. Contents Supplied • Impossibility of stopping the machine in the best possible conditions The drill press comes partially assembled and is • Variations in the rotational speed of tools shipped in carefully packed carton. After all the • Failure of the power supply parts have been removed from the carton, you •...

  • Page 7: Assembly And Installation

    7. Assembly & Installation Machine Head Place the machine head on the column tube and This drill press was partially assembled at the secure the machine head with the two grub screws to factory. To assemble your machine follow the below the side with the allen key 4 mm.
  • Page 8 Drill Chuck Drill Chuck Key Fold the drill chuck guard upwards. Insert the drill Attach the drill chuck key into the key holder. chuck on the taper of the drill spindle. Push the drill chuck onto the drill spindle with a few light taps. Use a plastic hammer for this purpose.
  • Page 9 8. Set Up Place the drill press on a solid flat surface. Ideally, bolt The gear cover is equipped with a the drill press to the surface. Use the two holes in the interlock switch. If the gear cover baseplate for this. is not closed correctly, the device Selecting the Speed cannot be switched on.
  • Page 10 Recommended speeds for different drill sizes and materials: Tensioning the V-belts Adjusting the Drilling Bench 1. Release the locking screw on the gear cover. 1. Release the locking handle. 2. Open the gear cover. 2. Push the drilling bench to the desired height. 3.

  • Page 11: Operation

    9. Operation 5. You can also adjust the tilt angle of the drilling bench. To do this, release the retaining screw under the drilling bench with an open end wrench SW 19 (not Always place a piece of backup material scope of delivery).

  • Page 12: Maintenance

    11. Maintenance Note: Feeding too slowly might cause the drill bit to turn in the chuck. Feeding too Note: Feeding too slowly might cause the rapidly might stop the motor, cause the drill bit to turn in the chuck. Feeding too belt to slip, force the workpiece loose, rapidly might stop the motor, cause the or break the drill bit.

  • Page 13: Troubleshooting

    12. Storage Danger! Store the drill press a way it cannot be started by unauthorised persons and that nobody can be injured. Caution! Do not store the drill press unprotected outdoors or in a moist environment. Store the device and its accessories in a dark, dry and frost-proof place that is inaccessible to children.
  • Page 14 Problem Cause Remedy Dirt, grease, or oil on the tapered surface on the Clean the tapered surface of both the chuck and spindle or in the chuck spindle with a household detergent.3. Repair Chuck falls off spindle by Customer Care. 1.
  • Page 16 Description Description Base 46 Upper Belt Cover Column Base 47 Circlip 5 Bolt 8.8 M8×20 48 Washer 6 Column 49 Screw M6×16 German Plug 50 Compression Spring Cable Sheath 51 V-Belt K460 Screw M4×8 52 Spacer Bush Cable Clamp 53 Idle Gear Screw ST3.5×9.5 54 Idle Gear Axle 10 Switch...
  • Page 17 Bench Drill - Part. No. DJMBD13-40 2006/42/EC Machinery Directive 2014/30/EU EMC Directive EN 62841-1:2015 EN 62841-3-13:2017 EN 55014-1:2017 EN 55014-2:2015 EN 61000-3-2:2014 EN 61000-3-3:2016 Date:05/17/2021...

Table of Contents