Table of Content Preface Table of Content ... 1-2 Regulations Information... 1-5 FCC-B Radio Frequency Interference Statement ... 1-5 FCC Conditions ... 1-6 CE Conformity ... 1-6 Safety Instructions... 1-7 Safety Guideline for Using Lithium Battery ...1-11 WEEE Statement ... 1-15 Trademarks ...
Page 3
Left Side View... 2-16 Rear Side View... 2-18 Bottom Side View ... 2-19 Getting Started Power Management ... 3-2 Connecting the AC Power ... 3-2 Using the Battery Power... 3-4 ECO Power Saving Function... 3-9 Power Management in Windows OS ... 3-10 Energy Saving Tips...
Page 4
BIOS Setup About BIOS Setup... 4-2 When to Use BIOS Setup... 4-2 How to Run BIOS Setup... 4-2 Control Keys ... 4-3 BIOS Setup Menu... 4-4 Main Menu... 4-5 Advanced Menu... 4-7 Boot Menu ... 4-9 Security Menu... 4-10 Save & Exit Menu ... 4-12...
Regulations Information FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Shield interface cables and AC power cord, if any, must be used in order to comply with the emission limits. FCC Conditions This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference.
Safety Instructions Read the safety instructions carefully and thoroughly. All cautions and warnings on the equipment or user’s manual should be noted. Keep the User’s Guide that comes with the package for future reference. Keep this equipment away from humidity and high temperature. Lay this equipment on a stable surface before setting it up.
Page 8
Make sure the power voltage is within safety range and has been adjusted properly to the value of 100~240V before connecting the equipment to the power outlet. Always unplug the AC power cord before installing any add-on card or module to the equipment.
Page 9
When installing the coaxial cable to the TV Tuner, it is necessary to ensure that the metal shield is reliable connected to protective earthing system of the building. Cable distribution system should be grounded (earthed) in accordance with ANSI/NFPA 70, the National Electrical Code (NEC), in particular Section 820.93, Grounding of Outer Conductive Shield of a Coaxial Cable.
Page 10
1-10 Green Product Features Reduced energy consumption during use and stand-by Limited use of substances harmful to the environment and health Easily dismantled and recycled Reduced use of natural resources by encouraging recycling Extended product lifetime through easy upgrades Reduced solid waste production through take-back policy Environmental Policy The product has been designed to enable proper reuse of parts and recycling and should not be thrown away...
1-11 Safety Guideline for Using Lithium Battery (English) CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the equipment manufacturer. Discard used batteries according to manufacturer’s instructions. (French) (Français) ATTENTION: II y a danger d’explosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avec une batterie du meme type ou d’un type équivalent recommandé...
Page 12
1-12 (Turkish) (Türkçe) UYARI: Pil yanlıs yerleştirilirse patlayabilir. Aynı ya da muadili bir pille degistiriniz. Kullanılmış pilleri üreticinin talimatlarına göre degerlendiriniz. (Greek) (Ελληνικά) ΠΡΟΣΟΧΗ: Κίνδυνος έκρηξης εάν η μπαταρία τοποθετηθεί λανθασμένα. Να αντικαθιστάτε μόνο με τον ίδιο ή αντίστοιχο τύπο με αυτό που συνιστά ο κατασκευαστής του εξοπλισμού. Να απορρίπτετε τις χρησιμοποιημένες μπαταρίες...
Page 13
1-13 (Korean) (한국어) 주의: 배터리를 올바로 교체하지 않으면 폭발할 위험이 있습니다. 타입이 장치 제조업체에서 권장하는 것과 동일하거나 동등한 배터리로만 교체하십시오. 사용한 배터리는 제조업체의 지침에 따라 폐기하십시오. (Vietnamese) (Tieng Viet) LƯU Ý: Thay thế pin không tương thích có thể dẫn đến nguy cơ bị nổ. Chỉ thay thế bằng pin cùng loại hoặc loại tương ứng khuyên dùng bởi nhà...
Page 14
1-14 (Portuguese) (Português) ADVERTÊNCIA: Perigo de explosão se a bateria é substituída incorrectamente. Substitua somente com o mesmo tipo ou equivalente recomendado por o fabricante do seu equipamento. Descarte as baterias utilizadas de acordo com as instruções do fabricante. (Swedish) (Svenska) VARNING: Explosionsfara vid felaktigt batteribyte.
1-15 (Croatian) (Hrvatski) OPREZ: Opasnost od eksplozije ako se baterija zamijeni neprikladnom. jednakom ili nadomjesnom vrstom prema preporuci proizvođača. proizvođača. (Estonian) (Eesti) ETTEVAATUST! Plahvatusoht, kui aku on valesti paigaldatud. Asendage ainult sama või tootja poolt soovitatud võrdväärse akuga. Hävitage kasutatud aku vastavalt tootja juhistele. در...
Page 16
1-16 (French) (Français) Au sujet de la directive européenne (EU) relative aux déchets des équipement électriques et électroniques, directive 2002/96/EC, prenant effet le 13 août 2005, que les produits électriques et électroniques ne peuvent être déposés dans les décharges ou tout simplement mis à la poubelle. Les fabricants de ces équipements seront obligés de récupérer certains produits en fin de vie.
Page 17
1-17 (Turkish) (Türkçe) Avrupa Birliği (AB) Kararnamesi Elektrik ve Elektronik Malzeme Atığı, 2002/96/EC Kararnamesi altında 13 Ağustos 2005 tarihinden itibaren geçerli olmak üzere, elektrikli ve elektronik malzemeler diğer atıklar gibi çöpe atılamayacak ve bu elektonik cihazların üreticileri, cihazların kullanım süreleri bittikten sonra ürünleri geri toplamakla yükümlü...
Page 19
1-19 (Indonesian) (Bahasa Indonesia) Elektronik), Directive 2002/96/EC, yang berlaku sejak 13, 2005, produk "peralatan listrik dan elektronik" tidak lagi dapat dibuang sebagai sampah umum dan pabrik peralatan elektronik diwajibkan untuk mengambil kembali produk tersebut pada saat masa pakainya habis. (Serbian) (Srpski) Po Direktivi Evropske unije ("EU") o odbačenoj ekektronskoj i električnoj opremi, Direktiva 2002/96/EC, koja stupa na snagu od 13.
Page 20
1-20 (Swedish) (Svenska) Under Europeiska unionens ("EU") Weee-direktiv (Waste Electrical and Electronic Equipment), Direktiv 2002/96/EC, vilket trädde i kraft 13 augusti, 2005, kan inte produkter från "elektriska och elektroniska utrustningar" kastas i den vanliga hushållssoporna längre och tillverkare av inbyggd elektronisk utrustning kommer att tvingas att ta tillbaka sådan produkter när de är förbrukade.
Page 21
1-21 (Norwegian) (Norsk) Under den europeiske unionens ("EU") direktiv om deponering av elektronisk og elektrisk utstyr, direktiv 2002/96/EC, som trer i effekt 13. august 2005, kan ikke produkter av "elektronisk og elektrisk ustyr" lenger deponeres som husholdningsavfall og fabrikantene av disse produktene er forpliktet å ta tilbake slike produkter ved slutten av produktets levetid.
1-22 Trademarks All trademarks are the properties of their respective owners. SRS Premium Sound, SRS and the symbol are trademarks of SRS Labs., Inc. Revision History Version Revision Note First release Date 12, 2009...
Congratulations on becoming a user of this notebook, the finely designed notebook. This brand-new exquisite notebook will give you a delightful and professional experience in using notebook. We are proud to tell our users that this notebook is thoroughly tested and certified by our reputation for unsurpassed dependability and customer satisfaction Manual Map This User’s Manual provides instructions and illustrations on how to operate this notebook.
Chapter 4, BIOS Setup, provides information on BIOS Setup program and allows you to configure the system for optimum use. Unpacking First, unpack the shipping carton and check all items carefully. If any item contained is damaged or missing, please contact your local dealer immediately. Also, keep the box and packing materials in case you need to ship the unit in the future.
Specification Physical Characteristic Dimension Weight Processor Type Support Processor L2 Cache FSB Speed Special Notification Core Chips North Bridge South Bridge Special Notification 265 (W) x 165 (D) x 19.8 ~ 25.4 (H) mm 900g (without battery pack) Micro-FCBGA8 ® Intel Atom processor...
Page 27
Memory Technology Memory Power AC/DC Adapter Battery Type RTC Battery I/O Port Monitor (VGA) Mic-in Headphone Out RJ45 Card Reader DDR2 667 DIMM slot x 1 Maximum up to 2GB (optional) 40W, 19V Input: 100~240V~1.5A 50~60Hz Output: 19V 2.1A 3 cell (optional) 6 cells (optional) 15 pin D-Sub x 1 x 3 (USB version 2.0)
Page 28
Storage (Items listed here may vary depending on the model users purchased) HDD form factor SSD (solid-state disk) Communication Port (Items listed here may vary without notice) Wireless LAN Bluetooth 3G/ 3.5G WiMax Audio Sound Interface Internal Speaker Sound Volume Video Dual View Function External Display Output...
Page 29
Display LCD Type Brightness Adjustment WebCam CMOS (optional) Software & BIOS USB Flash Boot BIOS Others Kensington Lock Hole Compliance 10.1", 1024 x 600 Supported Supported Yes, USB floppy boot up DOS only Fast Boot Support --- Yes WHQL...
Product Overview This section provides the description of basic aspects of the notebook. It will help you to know more about the appearance of this notebook before using it. Please be aware that the notebook shown in this section may vary from the actual one that users purchased. Top-open View The figure of top-open view and description shown below will lead you to browse the main operating area of your notebook.
Page 31
1. Webcam This built-in Webcam can be used for picture taking, video recoding or conferencing, and any other interactive applications. 2. Power Button / Power LED Press the power button to turn the notebook power ON and OFF. Press the power button to awake the notebook from the sleep state. Glowing blue when the notebook power is turned on.
Page 32
2-10 Wireless LAN / 3G/ WiMax (optional): Wireless LAN LED indicator glows green when Wireless LAN function is enabled. Wireless LAN LED indicator glows blue when 3G or WiMax function is enabled. LED indicator goes out when this function is disabled. Note: For flight safety consideration, make sure this LED indicator goes out when you are in flight.
Page 33
2-11 Hard Disk/ Optical Drive Device In-use: Blinking blue when the system is accessing the hard disk drive or the optical drive device. 5. Keyboard The built-in keyboard provides all the functions of a full-sized keyboard. Quick Launch [Fn] Buttons Use the [Fn] buttons on the keyboard to activate the specific applications or tools.
Page 34
2-12 Press and hold the Fn button, and then press the F11 button repeatedly to enable or disable the 3G or Bluetooth or WiMax function recurrently. Read the icon on behalf of the function of 3G or Bluetooth or WiMax appearing on the display to learn the function status. 3G/ Bluetooth/ WiMax Note that the functions listed here may vary depending on the...
2-14 Right Side View 1. Card Reader The built-in card reader may support various types of memory card, such as MMC (Multi-Media Card), SD (Secure Digital) cards. Contact the local dealer for further and correct information and be noted that the supported memory cards may vary without notice. 1.
Page 37
2-15 2. Audio Port Connectors Make high quality sound blaster with stereo system and Hi-Fi function supported. 3. USB Port The USB 2.0 port allows you to connect USB-interface peripheral devices, such as the mouse, keyboard, modem, portable hard disk module, printer and more. 4.
2-16 Left Side View 1. Kensington Lock This notebook provides a Kensington Lock hole, which allows users to secure the notebook in place with a key or some mechanical PIN device and attached through a rubberised metal cable. The end of the cable has a small loop which allows the whole cable to be looped around a permanent object, such as a heavy table or other similar equipment, thus securing the notebook in place.
Page 39
2-17 4. VGA Port The 15-pin D-sub VGA port allows you to connect an external monitor or other standard VGA-compatible device (such as a projector) for a great view of the computer display. 5. USB Port The USB 2.0 port allows you to connect USB-interface peripheral devices, such as the mouse, keyboard, modem, portable hard disk module, printer and more.
2-19 Bottom Side View 1. Battery Release Button It is a bounce-back device as a preparation for releasing the battery pack. Slide it with one hand and pull the battery pack carefully with the other. 2. Battery Pack This notebook will be powered by the battery pack when the AC/DC adapter is disconnected. Battery Release Button Battery Pack Battery Lock/ Unlock Button...
Page 42
2-20 3. Battery Lock/ Unlock Button Battery cannot be moved when the button is positioned on lock status. Once the button is slid to unlock position, the battery is removable. 4. Ventilator The ventilator is designed to cool the system. DO NOT block the ventilator for air circulation.
Power Management Connecting the AC power It is strongly recommended to connect the AC/DC adapter to the notebook and use the AC power while using this notebook for the first time. When the AC power is connected, recharging the battery will start immediately. Note that the AC/DC adapter included in the package is approved for your notebook;...
Page 45
Connecting the AC Power 1. Unpack the package to find the AC/DC adapter and power cord. 2. Attach the power cord to the connector of the AC/DC adapter. 3. Plug the DC end of the adapter to the notebook, and the male end of the power cord to the electrical outlet.
Using the Battery Power This notebook is equipped with a high-capacity Li-ion battery pack. The rechargeable Li-ion battery pack is an internal power source of the notebook. Be aware of that this battery pack may be damaged if users try to disassemble the battery pack on their own.
Installing the Battery Pack To insert the battery pack, following the steps below: 1. Use both hands to align and insert the battery pack into the compartment with correct orientation. 2. Slightly slide and press the battery pack into the right position until the battery back is fastened in the compartment.
Page 48
Releasing the Battery Pack It is always recommended to have another battery in reserve for enough power supply. Please contact your local dealer to buy a battery pack that is compliant to your notebook. To remove the battery pack, following the steps below: 1.
Battery Safety Tips Replacing or handling the battery incorrectly may present a risk of fire or explosion, which could cause serious injury. Only replace the main battery pack with the same or equivalent type of battery. Do not disassemble, short-circuit or incinerate batteries or store them to temperatures above +60°...
Charging the Battery Pack The battery pack can be recharged while it is installed in the notebook. Please pay attention to the following tips before recharging the battery: If a charged battery pack is not available, save your work and close all running programs and shut down the system or Save-to-Disk.
ECO Power Saving Function Enabling the ECO Engine ECO Engine, the outstanding and unique power saving function, provides various power saving modes – Gaming mode, Movie mode, Presentation mode, Office mode, and Turbo Battery mode, to extend the battery running time while performing different tasks with this notebook. Read the instructions bellow to activate the ECO Engine power saving function: 1.
Page 52
3-10 Presentation Mode Select this mode while performing presentation applications. Office Mode Select this mode while dealing with office documentation tasks. Turbo Battery Mode Select this mode to maximize the battery running time. ECO Off Selected to disable ECO Engine.
3-11 Power Management in Windows OS Power management of personal computers (PCs) and monitors has the poten-tial to save significant amounts of electricity as well as deliver environmental benefits.To be energy efficient, turn off your display or set your PC to standby/hibernate mode after a period of user inactivity. Follow the instructions below to adjust the power management settings in Windows OS: 1.
3-13 Energy Saving Tips Activate the ECO power saving function to manage the computer’s energy consumption. Turn off the monitor after a period of user inactivity. Utilize the Fn and F12 sleep mode keys to turn into power saving mode. Tune the settings in Power Options under Windows OS to optimize the computer’s power management.
3-14 Basic Operations If you are a beginner to the notebook, please read the following instructions to assure your own safety, and make yourself comfortable during the operations. Safety and Comfort Tips The notebook is a portable platform that allows you to work anywhere. However, choosing a good workspace is important if you have to work with your notebook for a long period of time.
3-15 1. Keep your hands and feet with optimal comfort. 2. Adjust the angle and position of LCD panel. 3. Adjust the desk’s height. 4. Sit straight and keep a good posture. 5. Adjust the chair’s height. Having a Good Work Habit Have a good work habit is important if you have to work with your notebook for long periods of time;...
3-16 Knowing the Keyboard This notebook provides a full-functioned keyboard. categories: Typewriter keys, Cursor keys, Numeric keys and Function keys. The keyboard shown here may vary from the actual one, depending on which county users purchase the notebook. This keyboard can be divided into four Typewriter keys Numeric keys Cursor keys /...
3-17 Typewriter Keys In addition to providing the major function of the keyboard, these typewrite keys also provide several keys for special purposes, such as [Ctrl,] [Alt,] and [Esc] key. When the lock keys are pressed, the corresponding LEDs will light up to indicate their status: Num Lock: Press and hold the [Fn] key and press this key to toggle the Num Lock on and off.
3-18 Cursor Keys The four cursor (arrow) keys and [Home], [PgUp], [PgDn], [End] keys are used to control the cursor movement. Move the cursor left for one space. Move the cursor right for one space. Move the cursor up for one line. Move the cursor down for one line.
3-19 The Backspace key, [Ins] and [Del] keys at upper right corner are use for editing purpose. This key is used to switch the typing mode between “insert” and “overtype” modes. Press this key to delete one character to the right of the cursor and move the following text left for one space.
Page 62
3-20 [Fn] Key Switch the display output mode between the LCD, external monitor and both. Enable or disable the touchpad function. Decrease the LCD brightness. Increase the LCD brightness. Decrease the built-in speaker’s volume. Increase the built-in speaker’s volume.
Page 63
3-21 Quick Launch [Fn] Buttons Webcam ECO Engine (Power Saving) Disable the computer’s audio function. Force the computer into sleep mode (depending on the system configuration). Press and hold the Fn button, and then press the F6 button to turn the Webcam function on.
Page 64
3-22 Press and hold the Fn button, and then press the F11 button repeatedly to enable or disable the 3G or Bluetooth or WiMax function recurrently. Read the icon on behalf of the function of 3G or Bluetooth or 3G/ Bluetooth/ WiMax appearing on the display to learn the function status.
3-23 Knowing the Touchpad The touchpad integrated in your notebook is a pointing device that is compatible with standard mouse, allowing you to control the notebook by pointing the location of the cursor on the screen and making selection with its two buttons. 1.
3-24 Using the Touchpad Read the following description to learn how to use the touchpad: Configuring the Touchpad You can customize the pointing device to meet your personal needs. For example, if you are a left-handed user, you may want to swap the functions of the two buttons. In addition, you can change the size, shape, moving speed and other advanced features of the cursor on the screen.
Page 67
3-25 Point and Click When you have moved and placed the cursor over an icon, a menu item or a command that you want to execute, simply tap slightly on the touchpad or press the left button to select. This procedure, called as point and click is the basics of operating your notebook.
3-26 About Hard Disk Drive Your notebook is equipped with a 2.5-inch hard disk drive. The hard disk drive is a storage device with much higher speed and larger capacity than other storage devices, such as the floppy disk drive and optical storage device.
3-27 Connecting the External Devices The I/O (input/output) ports on the notebook allow you to connect peripheral devices. All devices listed here are for reference only. Using the External Optical Storage Device An optional external optical storage device may come with the package of the notebook. The actual external optical storage device may vary depending on the model you purchased.
3-28 Connecting the Peripheral Devices Connecting the USB devices This notebook provides USB ports for connecting various USB devices, such as mouse, keyboard, digital camera, webcam, printer, and external optical storage device, ete.. To connect these devices, install the drivers for each device first if necessary, and then connect the device to the notebook.
Page 71
3-29 Connecting the External Display Devices This notebook provides a VGA port for connecting a larger display with higher resolution. The 15-pin D-sub VGA port allows users to connect an external monitor or other standard VGA-compatible device (such as a projector) for a great view of the notebook display. To connect the external display, make sure the notebook and the external display are both powered off, and then connect the display to the notebook.
3-30 Connecting the Communication Devices Using the LAN The RJ-45 connector of the notebook allows you to connect the LAN (local area network) devices, such as a hub, switch and gateway, to build a network connection. For more instructions or detailed steps on connecting to the LAN, please ask your MIS staff or network manager for help.
Page 73
3-31 Using Wireless LAN Connection (optional supported) This notebook is equipped with wireless LAN module which allows to users to perform fast data transmission with the standard IEEE 802.11 for wireless LAN. This gives users the mobility to move around within a broad coverage area and still be connected to the network. By using the 64-bit/128-bit Wired Equivalent Privacy (WEP) encryption technology and Wi-Fi Protected Access feature, the optional built-in wirelesses LAN is capable to achieve a more efficient and a more secure solution to the wireless communication.
Page 74
3-32 Using Bluetooth Connection (optional supported) This notebook is equipped with Bluetooth module which allows to users to connect various Bluetooth-enabled devices to the notebook. Bluetooth provides a way to connect and exchange information between devices such as mobile phones, personal computers, printers, GPS receivers, PDAs, digital cameras, and video game consoles through a secure, globally unlicensed Industrial, Scientific and Medical (ISM) 2.4 GHz short-range radio frequency bandwidth.
3-33 Safely Remove Hardware When any peripheral device is connected to the notebook, the Safely Remove Hardware icon will appear on the taskbar. Double-click the icon to bring up the Safely Remove Hardware dialog box. You can see all connected peripheral devices here. If you want to remove any of the devices, move the cursor to the device and click Stop.
3-34 Components Replacement and Upgrade Please be noticed that the memory, hard disk drive, wireless LAN module and battery pack preinstalled in the product users purchased may be upgradable or replaceable by user’s request depending on the models users purchased.
Page 77
3-35 This notebook is equipped with a high-capacity Li-ion battery pack, and the battery pack is replaceable by users. To replace the battery pack, please refer to the section of Using Battery power for details. This notebook is equipped with a wireless LAN module, and the module may be upgradable and replaceable by authorized dealer or service center.
Page 78
3-36 To learn more about upgrade limitation, please refer to the specification in the User’s Manual provided. For any further information about the product users purchased, please contact the local dealer. Do not attempt to upgrade or replace any component of the product, if you are not an authorized dealer or service center, since it may cause the warranty void.
About BIOS Setup When to Use BIOS Setup? You may need to run the BIOS Setup when: An error message appears on the screen during the system booting up and is requested to run SETUP. You want to change the default settings for customized features. You want to reload the default BIOS settings.
Control Keys You can use only the keyboard to control the cursor in the BIOS Setup Utility. Press left arrow to select one menu title. Press up arrow to select one item under the menu title. 1) Open the selected item to change setting options. 2) Bring up a sub-menu when available.
BIOS Setup Menu Once you enter the BIOS Setup Utility, the Main Menu will appear on the screen. Select the tags to enter the other menus. Main Menu Show system overview information about BIOS version, CPU features, memory size and setting of system time and date. Advanced Menu Adjust the advanced settings, such as power consumption, USB/ PCI devices, of the notebook in order to achieve a better performance.
Main Menu System Date This item allows you to set the system date. [day:month:date:year]. Month (Month) Date (Date) Year (Year) System Time This item allows you to set the system time. The system clock will go on no matter you shut down the PC or get into sleep mode. The time format is [hour:minute:second].
Page 84
System Information This item provides the information about the firmware, processor, and system memory.
Advanced Menu Intel SpeedStep This item allows you to enable or disable Intel SpeedStep technology. When set to Disabled, the system always operates in a conserve power mode (the processor works at FSB400-600MHz or FSB533-800MHz). If you want optimize the processor, set this item to Enabled, so that the processor’s speed will be controlled by the use of your operating system and applications.
Page 86
PCI Latency Timer This item controls how long each PCI device can hold the bus before another takes over. When set to higher values, every PCI device can conduct transactions for a longer time and thus improve the effective PCI bandwidth.
Boot Menu Set Boot Priority These items showing the sequence of boot devices where BIOS attempts to load the disk operating system. Boot Option #1~6 These items allow you to set the sequence of boot devices where BIOS attempts to load the disk operating system.
4-10 Security Menu Supervisor Password / User Password When this item is selected, a message box shall appear on the screen as below: Enter New Password Type a maximum of eight-digit password and press [Enter]. password typed now will replace any previously set password from CMOS memory.
Page 89
4-11 The Password Check item is used to specify the type of BIOS password protection that is implemented. Settings are described below: Setup Always To clear a set Supervisor Password/ User Password, just press [Enter] under Supervisor Password/ User Password field when you are prompted to enter the password.
4-12 Save & Exit Menu Exit and Save Changes Save the changes you have made and exit the utility. Exit and Discard Changes Exit the utility without saving the changes you have made. Load Setup Defaults Select this item to load the default settings.