Advertisement
Quick Links
DUST & CHIP EXTRACTOR
OWNERS MANUAL
MODELS: W792, W792/3, W792CF, W792/3CF
A 16 amp fixed electric
supply is required to run
this machine.
Recommended breaker size:
16 Amps (Type C)
Charnwood, Cedar Court, Walker Road,
Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU
Tel. 01530 516 926
email: sales@charnwood.net
website: www.charnwood.net
1
Advertisement
Summary of Contents for Charnwood W792
- Page 1 DUST & CHIP EXTRACTOR OWNERS MANUAL MODELS: W792, W792/3, W792CF, W792/3CF A 16 amp fixed electric supply is required to run this machine. Recommended breaker size: 16 Amps (Type C) Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel.
-
Page 2: General Safety Rules
GENERAL SAFETY RULES WARNING: Do not attempt to operate the machine until you have read thoroughly and understood completely all instructions, rules, etc. contained in this manual. Failure to comply may result in accidents involving fire, electric shock, or serious personal injury. Keep this owner's manual and review frequently for continuous safe operation. - Page 3 7. DO NOT use without the filter bag and collection bag in place. 8. Keep hair, loose clothing, fingers, and all parts of the body away from the end of the suction hose. W792 Specification Motor (Available in 240v single phase or 415v 3 phase)
- Page 4 Unpacking This machine is supplied in 2 cartons. Open the cartons and carefully unpack all of the contents. Right Collector Body Column Collection Bag Left Collector Body Filter Bag Bag Straps Motor Assembly Lower Support Leg Castors 3 Way Inlet Upper Support Leg Fixings Pack Rubber Gasket...
- Page 5 Assembly Join The Base Use 4 x Hex head screws 5/16” x 1/2“, to attach 2 Joining Brackets to one end of the base. Push the 2 base panels together and Use 4 more screws to attach the bracket. Tighten with a 12mm spanner, or socket set Attach The Castors Turn the assembled base upside down.
- Page 6 Secure with 3 Hex head screws, 1/4” x 1/2" Tighten with a 10mm spanner or socket Fit The Column & Motor Assembly To The Base Flip the motor assembly right way up and place it onto the base aligning with the four mounting points.
- Page 7 Fit the Left Collector Body Place the Rubber Gasket between the 2 parts. Tip: Use a G clamp to hold the 2 parts in place whilst fitting the screws Use 8 Hex Head screws, 5/16” x 1/2" to secure the Collector Body to the impellor housing Attach the Support Leg to the Left Collector Body...
- Page 8 Fit the Right Collector Body Place the Rubber Gasket between the 2 parts. Use 6 Hex head screws 1/4" x 1/2” to secure the Right Collector Body to the impellor housing Tighten with a 10mm spanner or socket Then secure The Right Collector Body to the Leg Support using 2 Hex head screws, 5/16”...
- Page 9 Fit the Handle Use 2 Hex head screws 1/4" x 1/2” Fit 4 Foam Sealing Strips Take a roll of Self Adhesive Foam, peel off the backing paper and stick it to the outside upper rim of the Collector Body. Use a pair of scissors to trim off any excess.
- Page 10 Fit the Filter Bag Locate the rectangle opening in the open end of the Filter Bag. Feed the Bag Strap into the pocket all the way around the full circumference of the bag, until it can be seen in the opening again.
-
Page 11: Optional Items
The standard cloth filter, filters down to 2 microns. This optional cartridge replaces the cloth bag and filters down to 1 micron without any loss in performance. NB The W792 has 2 filters and both would need to be upgraded to achieve the 1 micron filter level. -
Page 12: Troubleshooting
Troubleshooting Reduced Performance Check the collection bag is not full. Empty or replace the bag as required. Check the filter bag is not clogged. Turn the bag inside out and scrape the inside clean. The filter bag can also be washed, ensure it is completely dry before refitting. -
Page 13: Declaration Of Conformity For Ce Marking
Declaration of Conformity for CE Marking Charnwood Declare that Woodworking Dust Extractor, Models: W792, W792CF, W792/3 & W792/3CF Conforms with the following Directives: Machinery Directive 2006/42/EC Low Voltage Directive 2006/95/EC Conforms with the following UK Regulations: Supply of Machinery (Safety) Regulations 2008 Electrical Equipment (Safety) Regulations 2016 And further conforms to the machinery example for which the EC type examination Certificate No. - Page 14 Charnwood W792 Parts List Part No. Description Quantity Castor Hex Head Screw 5/16” x 1/2“ Base Joining Bracket Base Plate (Left & Right) Column Motor (Available in 240v or 415v) Hex Head Screw 1/4" x 1/2" On/Off Switch (Available in 240v or 415v)
- Page 15 CHARNWOOD W792 EXPLODED VIEW DIAGRAM...
- Page 16 Update October 2022 Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 email: sales@charnwood.net website: www.charnwood.net...
- Page 17 To clean the filter, daily (or after each use if used less frequently) make one complete rotation of the handle in both clockwise and anti-clockwise directions. This will dislodge trapped dust particles which will fall into the collection bag. Charnwood, Cedar Court, Walker Road, Hilltop Industrial Estate, Bardon Hill, Leicestershire, LE67 1TU Tel. 01530 516 926 email: sales@charnwood.net...