HIMEDIA Company #507, ACE-Gunpo, 52, Gongdan-ro 140 beon-gil, Gunpo-si, Gyeonggi-do, Korea T +82. 31. 478. 8182 F +82. 31. 696. 6537 E jeff@hi-media.co.kr H www.hi-media.co.kr HM-LC43R15J PANEL Specification NOTE Specification is subject to change without notice. Conseuently it is better to contact to our company before proceeding with the design of your product incorporating this Panel.
/ 31 2. General Description and Features This specification applies to the 43 inch Color TFT-LCD SKD model HM-LC43R15J. This Open Unit has a TFT active matrix type liquid crystal panel with 3840 x 2160 pixels and V by one interface;...
The relative humidity must not exceed 90% non-condensing at temperatures of 40℃ or less. At temperatures greater than 40℃, the wet bulb temperature must not exceed 39℃. Note 4. Surface temperature is measured at 50℃ Dry condition. PANEL HM-LC43R15J Rev. 1.0...
0.104 0.289 White 0.339 Viewing Angle Note 5,9 φ=0 θ degree x axis, right( °) φ=180 θ degree x axis, left( °) φ=90 θ degree x axis, up( °) x axis, θ degree φ=270 down( °) PANEL HM-LC43R15J Rev. 1.0...
Page 8
The response time is defined as the following figure and shall be measured by switching the input signal for “any level of gray(bright)” and “any level of gray(dark)”. Fig. 3 Response Time PANEL HM-LC43R15J Note 8. Light source here is the standard light source “C” which is defined by CIE and driving voltages Rev. 1.0 are based on suitable gamma voltages.
Page 9
Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to the LCD surface. For more information see FIG4. Fig. 4 Viewing Angle PANEL HM-LC43R15J Rev. 1.0...
/ 31 5. Interface Specification 5.1 Input power This HM-LC43R15J Open Cell Unit requires power input which is employed to power the LCD electronics and to drive the TFT array and liquid crystal. Value Item Symbol Unit Note Min. Typ.
GND or N. C. RX6P Vx1 lane 6 (for us test only. Do not connect) No Connection N.C. Ground (for us test only. Do not connect) Ground RX7N Vx1 lane 7 HTPDN Vx1 HTPDN RX7P Vx1 lane 7 Ground PANEL HM-LC43R15J Rev. 1.0...
Page 12
Start Setup Time tSTASU 0.26 Start Hold Time tSTAHD 0.26 Stop Setup Time tSTOSU 0.26 Data In Setup Time tDSU Data In Hold Time tDHD SCL / SDA Rise Time 0.12 SCL / SDA Fall Time 0.12 PANEL HM-LC43R15J Rev. 1.0...
Page 13
/ 31 Input equivalent impedance of SDA / SCL pin Note 17. Write Protection Mode selection Note L or OPEN Protection Writable Input equivalent impedance of WP pin PANEL HM-LC43R15J Rev. 1.0...
Page 14
D [22] B/Cb [8] D [23] B/Cb [9] D [24] D [25] D [26] B/Cb [0] D [27] B/Cb [1] Byte3 D [28] G/Y [0] D [29] G/Y [1] D [30] R/Cr [0] D [31] R/Cr [1] PANEL HM-LC43R15J Rev. 1.0...
Page 15
COLOR DATA REFERENCE Input Color Data GRREN BLUE Color Black Red(1023) Green(1023) Blue(1023) Basic Colors Cyan Magenta Yellow White Red(000) Red(001) Red(1022) Red(1023) GREEN(000 GREEN(001 GREE GREEN (1022) GREEN (1023) BLUE(000) BLUE (001) BLUE BLUE (1022) BLUE (1023) PANEL HM-LC43R15J Rev. 1.0...
Page 16
Max. Period 2200 2250 2715 Vertical Section Active Tdisp (V) 2160 Blanking Tblk (V) Period Tclk Horizontal Section Active Tdisp (V) Blanking Tblk (V) Tclk Clock Frequency Fclk=1/Tclk 74.25 Vertical Frequency Frequency Horizontal Frequency Frequency 139.2 PANEL HM-LC43R15J Rev. 1.0...
Page 17
/ 31 The timing diagrams of the input timing (Lane 1~8 V-by one data : 1, 2, 3, 4, 1921, 1922, 1923, 1924) PANEL HM-LC43R15J Rev. 1.0...
Page 18
8b10b data CML Differential Input High Threshold CML Differential Input Low Threshold CML Common mode Bias Voltage V-by-one Interface Intra-pair skew Note 19 INTRA Inter-pair skew Note 20 INTER 0.25 Eye diagram at receiver Note 21 0.75 PANEL HM-LC43R15J Rev. 1.0...
Page 19
/ 31 Note 17. V-by-one Signal diagram Note 18. Receiver Clock SSCG (Spread spectrum clock generator) is defined as below figures. Note 19. V-by-one Intra-pair Skew PANEL HM-LC43R15J Rev. 1.0...
Page 20
/ 31 Note 20. V-by-one Inter-pair Skew Note 21. Eye diagram at receiver Eye Mask Example of Eye diagram PANEL HM-LC43R15J Rev. 1.0...
Page 21
(1) t4=0 : concern for residual pattern before BLU turn off. (2) t6 : voltage of VDD must decay smoothly after power-off. (customer system decide this value) (3) When user control signal is N.C. (no connection), opened in Transmitted end, t8 timing spec can be negligible. PANEL HM-LC43R15J Rev. 1.0...
(f) It is recommended to peel protection films off as slowly as possible. (Constant speed more than 8 seconds per film.) (g) The protection film should not be contacted to the IC(source and gate) or source PCB. PANEL HM-LC43R15J Rev. 1.0...
(a) Be cautious not to give any strong mechanical shock or any forces to the panel kit. Applying any forces to the panel may cause the abnormal operation or the damage to the panel kit and the back light unit kit. PANEL HM-LC43R15J Rev. 1.0...
Page 31
(g) The module has high frequency circuits. The sufficient suppression to the electromagnetic interference should be done by the system manufacturers. The grounding and shielding methods is important to minimize the interference. The sufficient suppression to the EMI should be done by the set manufacturers. PANEL HM-LC43R15J Rev. 1.0...
Page 32
R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B R G B PANEL HM-LC43R15J Rev. 1.0...
Page 33
Device Address + W Control Address Write DAC to NVM + OUT_EN Step 5 Reset Device Address is 0x74 (7Bits) Index Address Slave Address Control Byte 0xE8 0x00 0x12 Device Address + W Control Address Reset + OUT_EN PANEL HM-LC43R15J Rev. 1.0...