Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for Total UTMGT1601
- Page 1 说明书材质要求:105g铜版纸 说明书成品尺寸: 148x210mm 第一:专色+CMYK油墨要求： 第二：特别注意： 1.印刷时看样颜色请参考我司提供的实物样品颜色,不得偏色。 1.TOTAL专色油墨，见实物色样调整 2.322C的专色不得参考C=100,M=28.42,Y=48.29,K=21.6 对应的四色色谱颜色来看样印刷 2.C色油墨:泗联天蓝墨 3.M色油墨:泗联洋红墨 4.Y色油墨:泗联中黄墨 5.K色油墨:泗联黑墨 折叠方式：骑马钉 备注: 特别注意：此页内容不印刷 1.参考TMGT1601 2022.4.9 T0422.V01...
- Page 2 INVERTER MAG/MIG/MMA/TIG LIFT WELDING MACHINE UTMGT1601 TOTAL TOOLS WORLD SCAN FOR VIDEO 160A...
- Page 3 Instruction manual for UTMGT1601 Kindly please keep this manual for safety warnings and precautions, assembly, opera- tion, inspection, maintenance and cleaning procedures. Keep this manual in a safe and dry place for future reference. WARNING! Read this manual before using this machine. Failure to do so may result in serious injury.
-
Page 4: Protect Yourself And Others
WARNING Reading all safety instructions and warnings. Failure to do so may result in serious injury. Keep this manual in a safe and dry place for future reference. Safety PROTECT YOURSELF AND OTHERS. Please read and understand this information. 5. Stay alert, watch what you’re doing and 1. - Page 5 Fume and gas Safety INHALATION HAZARD Welding and Plasma cutting produce toxic fume. 1. Exposure to welding or cutting exhaust 4. Use enough ventilation, exhaust at arc, or fumes can increase the risk of developing both, to keep fumes and gases from breath- certain cancers, such as cancer of larynx ing zone and general area.
-
Page 6: Electrical Safety
Electrical Safety 1. Turn off, disconnect power, and 6. Do not expose welders to rain or wet condi- discharge electrode to ground before Water entering a welder will increase the risk tions. setting down torch/electrode holder and of electric shock. before service. - Page 7 Controls Front panel Controls...
- Page 8 Back panel Controls Power Gas inlet on/off...
-
Page 9: Mig/Flux-Cored Wire Welding
Interior Controls MIG/Flux-cored wire welding Read the entire important safety information section at the very beginning of this manual including all text under subheadings therein before set up or use of this item. WARNIN TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: TURN THE POWER SWITCH OFF AND UNPLUG THE WELDER BEFORE SET UP. - Page 10 Feed roller instructions: Notice: Notice: IMPORTANT! Securely hold onto the end of the welding wire and keep tension on it during the following steps. If this is not done, the welding wire will unravel and unspool which can cause tangling and feeding problems. DANGER PARTS MAY BE AT WELDING VOLTAGE TO PREVENT ELECTRIC SHOCK AND DEATH...
- Page 11 50-120A 30-120A 70-180A 50-300A 80-350A 60-440A 140-500A 120-550A Basic wire welding READ THE ENTIRE IMPORTANT SAFETY INFORMATION WARNING TO PREVENT SERIOUS INJURY: Protective gear must be worn when using the Welder; minimum shade number 10 full face shield or welding mask), ear protection, welding gloves, sleeves and apron, NIOSH-approved respirator, and fire resistant work clothes without pockets should be worn when welding.
- Page 12 TIG/MMA welding 110/220Vac. Electrode(mm) Welding 25-40A 40-60A 50-80A 100-130A 160-180A current(A) Lift TIG Electrode(mm) Welding 10-75A 40-130A 75-180A 130-230A 160-310A current(A) Basic TIG/MMA welding READ THE ENTIRE IMPORTANT SAFETY INFORMATION WARNING TO PREVENT SERIOUS INJURY: Protective gear must be worn when using the Welder;minimum shade number 10 full face shield or welding mask) ,ear protection,welding gloves,sleeves and apron, NIOSH-approved resistant work clothes without pockets should be worn when welding.
-
Page 13: Maintenance
Make practice welds on pieces of scrap to practice technique before welding anything of value. Maintenance WARNING TO PREVENT SERIOUS INJURY, FIRE AND BURNS: Unplug the Welder,rest the tool on a heat-proof, electrically non-conductive surface, and allow all parts of the Welder to cool thoroughly before service. - Page 14 UTMGT1601 Exploded view...
- Page 15 UTMGT1601 Spare part list Part Description Qty NO. Part Description Handle Bottom cover Top cover Control PCB Solenoid valve Panel PCB PG clip Insulation base Power cable Joint DC fan Knob Insulation paper Quick connector(red) Switch Quick connector(black) Main PCB...
- Page 16 INVERTER MAG/MIG/MMA/ TIG LIFT WELDING MACHINE www.totalbusiness.com TOTAL TOOLS CO., PTE. LTD. No. 45 Songbei Road , Suzhou Industrial Park , China. MADE IN CHINA T0422.V01 160A...
Need help?
Do you have a question about the UTMGT1601 and is the answer not in the manual?
Questions and answers