Page 1
OWNER’S MANUAL TYPE: SSDP37-- Robotic Cleaner WARNING FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product must be serviced by a pool technician who is licensed and qualified in pool equipment by the jurisdiction in which the product will be installed where such state or local requirements exist.
Page 2
JACUZZI JAG ROBOTIC CLEANER ® FCC STATEMENT This device complies with Part 15 of the FCC Rules and IC licence-exempt RSS standard. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
OWNER'S MANUAL TABLE OF CONTENTS Section 1. Important Safety Instructions ..4 Section 2. Cleaner specifications ....5 General Specifications ..............5 Section 3. Connect to Power ......5 Section 4. Install the Cleaner ......6 Submerge in the Pool ..............6 Start / Stop Cleaning ..............7 Optimal Patterning/Cable Tangling ........8 Remove from Pool ................8...
JACUZZI JAG ROBOTIC CLEANER ® SECTION 1. IMPORTANT SAFETY INSTRUCTIONS Please read through the entire manual before installing your new robotic pool cleaner. The cleaner must be installed and operated as specified. WARNING Failure to comply with the following warnings can result in permanent injury, electrocution or death.
OWNER'S MANUAL CAUTION Failure to comply with the following warnings could cause damage to pool equipment or personal injury. • The cleaner must be installed and operated as specified. • Clean out the debris from the cleaner after each use. •...
JACUZZI JAG ROBOTIC CLEANER ® SECTION 4. INSTALL THE 1. Plug power supply into a GFCI outlet (Ground Fault Circuit Interrupter) (Figure 1). Power Supply CLEANER must be 5 ft. from the pool's edge. CAUTION To prevent damage to the cleaner, be sure to adhere to the following guidelines: •...
OWNER'S MANUAL Midpoint of the long side of pool 12 ft / 4 m Figure 5. Spread Floating Cable to Prevent Tangling START / STOP CLEANING 1. Press On/Off button to begin or interrupt cleaner operation (Figure 6). Figure 3. Pool Entry Point for Optimal Patterning 2.
JACUZZI JAG ROBOTIC CLEANER ® OPTIMAL PATTERNING/CABLE 2. Gently pull the cleaner up to the waterline TANGLING (Figure 11). It is recommended to alternate the angle and direction of the cleaning path every cleaning cycle to ensure the cleaner is covering the whole pool, as well as prevent cable tangling.
OWNER'S MANUAL Figure 16. Rinse Figure 13. Remove the Cover 6. Replace back into the cleaner body and replace 3. Pull gently on the elastic band around the suction the cover. ports to release the filter bag (Figure 14). 7. Store the cleaner out of direct sunlight for next use. STORE THE CLEANER WHEN NOT IN USE Do not leave the cleaner in the pool when not in...
JACUZZI JAG ROBOTIC CLEANER ® 3. Adjust wheel direction after every cleaning cycle. Adjusting wheel direction ensures your cleaner reaches all areas of the pool and prevents cable tangling. Figure 18. Long Term Storage for Extended Period SECTION 5. MAINTENANCE...
OWNER'S MANUAL SECTION 6. SPARE PARTS Contact an authorized service center to perform diagnostic tests or repairs not shown in general maintenance. SECTION 7. TROUBLESHOOTING The following provides some helpful hints for troubleshooting common issues when using the cleaner. Problem Solution Cleaner moving too slowly/not •...
Page 12
Jacuzzi Inc. All other brands, product names, company names, trade names and ® trademarks used are the property of their respective owners. Jacuzzi may add to change or remove any part of these materials at any time, without notice. Reproduction in whole or inpart without written permission is prohibited.
Need help?
Do you have a question about the JAG and is the answer not in the manual?
Questions and answers